Installation Instructions - JUNO FIREWALL FIRE RATED 4 IC4ALFW Instrucciones De Instalación

JUNO FIREWALL™ FIRE RATED 4" INTERNALLY ADJUSTABLE LED
NEW CONSTRUCTION RECESSED HOUSINGS
TRIM INSTALLATION
Step 1. After ceiling is finished and painted, remove and discard paint
shield from fixture.
Step 2. Aim the fixture as desired: Adjustment angles range 0-35º.
It is recommended that the fixture always be aimed without a trim installed
and the fixture off.
The light engine heat sink slides along the frame in the recessed housing.
Grasp the optic holder and slide it on a slight curve to change the adjustment
angle. The sliding motion changes the angle of the light source (Fig. 8).
The heatsink and frame assembly can be rotated about the center axis
of the housing to aim the light (Fig. 9).
Step 3. Use 1/16" allen wrench to lock fixture adjustment if desired (Fig. 10).
Step 4. After the fixture is aimed, the trim needs to be oriented correctly
and installed in the housing. If the trim is an "angle cut" trim, it is
necessary to orient the portion of the trim that is lower near the optic
(Fig. 11).
DRIVER REPLACEMENT
Driver replacement must be performed by a qualified electrician.
Before servicing, disconnect or switch off electrical supply to the fixture.
Failure to do so can result in electrical shock and/or injury.
Step 1. Remove trim (Fig. 12).
Step 2. Remove 3 screws that secure inner housing to the plaster frame.
Inner housing will slide out of fixture (Fig. 12).
Step 3. Disconnect leads from driver to inner housing and set inner
housing aside.
Step 4. Now access the fixtures wiring by carefully pulling it through the
opening. Once exposed you can proceed with disconnecting the AC
leads that provide power to the driver and any applicable dimming wires.
Step 5. Lift fire barrier flap on the side with the red and black wires
protruding (red and black wires indicate driver location). The bottom of the
flap will have a half moon finger slot for easy lifting (Fig. 13). Before lifting
the flap, make sure the wires are pushed out of the wire slots provided in
the flap to prevent tearing the fire barrier. This will allow access to the
LED driver (Fig. 14).
Step 6. Remove wing nut from driver plate to remove driver plate from
fixture (Fig.15). Pull driver plate out while slightly lifting to release lower
mounting feet. Once free pull plate towards fixture opening and rotate
plate 90° so it will fit through fixture opening. Driver plate rubbing against
fire barrier is acceptable.
Step 7. Re-assemble fixture by completing steps 1 thru 6 in reverse order.
JUNCTION BOX ACCESS
Step 1. Remove trim (Fig. 12).
Step 2. Remove 3 screws that secure inner housing to the plaster frame.
Inner housing will slide out of fixture (Fig. 12).
Step 3. Disconnect leads from driver to inner housing and set inner
housing aside.
Step 4. Now access the fixtures wiring by carefully pulling it through the
opening. Once exposed you can proceed with disconnecting the AC
leads that provide power to the driver and any applicable dimming wires.
Step 5. Lift fire barrier flap on the side with the red and black wires
protruding (red and black wires indicate driver location). The bottom of the
flap will have a half moon finger slot for easy lifting (Fig. 13). Before lifting
the flap, make sure the wires are pushed out of the wire slots provided in
the flap to prevent tearing the fire barrier. This will allow access to the
LED driver (Fig. 14).
Step 6. Open junction box door inside of fixture by lifting black spring
retention clip. Once junction box door is released pull door out while
slightly lifting to release lower mounting feet. Once free pull plate towards
fixture opening and rotate plate 90° so it will fit through fixture opening.
Junction box door rubbing against fire barrier is acceptable.
Step 7. Re-assemble fixture by completing steps 1 thru 6 in reverse order.
OPTIC REPLACEMENT OR ADDING MEDIA
Step 1. Unscrew face from optic holder.
Step 2. Replace with desired new optic.
Step 3. Screw optic holder into place. Be sure that optic seats in the
pocket in the optic holder and does not become trapped between the
lips of the holder and face.
WARRANTY
5-year limited warranty. Complete warranty terms located at
Technical Services Phone 1-800-705-SERV (7378)
One Lithonia Way • Conyers GA 30010 • Phone 1-800-705-SERV (7378) • Visit us at www.acuitybrands.com/juno-recessed
©2020 Acuity Brands Lighting, Inc

INSTALLATION INSTRUCTIONS

Figure 9
Screws
Trim
Figure 12
Junction
Box
Figure 1 4
www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx
Rev 06/20 P4746
Figure 8
Lock Screw
Figure 10
HALF MOON
FINGER SLOT
LED
Driver
Align
Figure 11
Figure 13
WING NUT
Figure 15
2 of 2