Installation Of The Kiros I-Size Child Car Seat On The I-Size Base - Chicco BebeCare Kiros i-Size Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 39
approved vehicle seats (check the vehicle's in-
struction manual) and on seats of vehicles in-
cluded in the "Vehicle compatibility list" given
with the child car seat.
In any event the vehicle seat must be forward
facing. Never use this car seat rear facing on
any vehicle's seat (Fig. 2).
- When the vehicle's 3 point seat belts (without
the i-Size base). In any event the vehicle seat
must be forward facing. Never use this car seat
rear facing on any vehicle's seat (Fig. 2). The
vehicle's seat must be equipped with either
static or retractable 3-point safety harnesses
approved according to UN/ECE Regulation
R16 or other equivalent standards (Fig. 3).
WARNING! Never fit the child car seat to a ve-
hicle seat that is only equipped with a 2-point
seat belt (Fig. 4).
WARNING! If it is used in a vehicle equipped
with rear safety harnesses with integrated air-
bags (inflatable seat belts), the interplay be-
tween the inflatable portion of the seat belt and
this child restraint system could cause serious
injury or death. Do not install this child restraint
equipment where an inflatable safety harness
must be used. Install it using the Isofix system
or move the child car seat to a suitable type of
safety harness. During installation with the Isofix
system, the safety harness may not be fastened
behind the child car seat, as this would engage
the inflatable portion of the safety harness.
WARNING! SERIOUS DANGER! Never use this
device fitted on front vehicle's seats equipped
with a front airbag. It is possible to fit the i-Size
base and the child car seat on a front seat only
if the front airbag has been deactivated: check
with the car manufacturer or see the owner's
manual for instructions on how to deactivate
the airbag. It is always recommended to slide
the vehicle seat as far back as possible de-
pending on whether passengers are travelling
on the back seat or not.
2. CAR INSTALLATION
2.1 INSTALLATION AND REMOVAL OF THE
I-SIZE BASE
Proceed as indicated to install the i-Size base:
1. Remove the plastic cover from the Support
Leg (Fig. 5)
2. Extract the support leg (G) (Fig. 5A). An
acoustic signal will activate and stop when
the i-Size base has been installed correctly.
3. Completely extract both Isofix connectors
(A) of the base by pulling the connector ex-
traction lever (B) (Fig. 6). Make sure that the
system is extracted to the end stop.
4. Position the i-Size base on desired seat and
fasten the Isofix connectors to the anchor-
age points found between the backrest and
the vehicle seat (Fig. 7). You will hear a "click"
when the connectors fit into place.
WARNING! Make sure that the connection
was made correctly by checking that the two
indicators (C) are green.
5. Push the i-Size base firmly against the back-
rest of the vehicle seat (Fig. 8) to make sure
it is securely in place.
6. Check that the two connectors are fastened
correctly by trying to pull the base multiple
times.
7. Position the support leg (G) and adjust it
using the adjustment button (H) (Fig. 9).
When the support leg is installed correctly,
the acoustic signal will stop and at the same
time, the indicator (I) will turn green (Fig. 10).
REMOVAL
Press the support leg adjustment button (H)
and shorten it to the end stop. Lift the ISOFIX
connector extraction lever (B) and move the
base away from the backrest to the end stop.
Release the ISOFIX connectors by pushing the
release buttons (D) (Fig. 11).
While holding down the ISOFIX connector ex-
traction lever (B), push the ISOFIX system into
the base, making sure to reach the end stop.
Turn the support leg and fasten the feet in the
provided slot, deactivating the acoustic signal.
2.2 INSTALLATION OF THE KIROS I-SIZE
CHILD CAR SEAT ON THE I-SIZE BASE
Before fastening the child car seat on the i-Size
base, make sure that the 4 hooks are open cor-
rectly; to check this, simply press the two Y le-
vers located to the sides of the base (Fig. 12A).
1. Fasten the child car seat on the i-Size base
19

Publicidad

Tabla de contenido
loading

Tabla de contenido