Placing The Child In The Seat - Chicco AUTO-FIX Instrucciones De Uso

WARNING! Never fi t the child car seat in a car
seat which is only equipped with a 2 point car
safety belt safety belt (diag. 2A).
ADJUSTING THE RESTRAINT HARNESS
WARNING! The restraint harness must always
be adapted according to your child's growth.
Before fi tting the chid car seat into the car, adjust
the child restraint harnesses to the correct height.
The correct position of the harness height is
slightly below your child's shoulders (diag. 3). The
child car seat can be adjusted to 3 positions (diag. 4).
The child car seat is equipped with a comfort
cushion, which guarantees the correct fastening
of your child and the ideal position for neck and
back, from birth until the child weighs 6 kg.
To fi t the comfort cushion, check that the belts
are inserted in the hole placed in the lowest
position. WARNING: this is the only position
allowed for using the child car seat with the
comfort cushion (diag. 5).
Warning: to guarantee the maximum safety of
the product, remove the comfort cushion when
the child weighs 6 Kg.
To adjust the restraint harnesses, proceed as follows:
Open the buckle by pressing the red button (diag. 6).
Remove the harness from the back and insert it
into the hole, which is the most suitable one for
your child's height.
(diag. 7A and 7B).
WARNING! Ensure that the safety harness is
always inserted between the roller bar and the
child car seat's shell.
The safety harness must always be tightened to
the correct position.

PLACING THE CHILD IN THE SEAT

1. Lift the fabric fl ap, keep the adjusting button
pressed and pull the child car seat harness to
untighten it (diag. 8).
2. Open the buckle by pressing the red button (diag. 6).
3. Place the child.
4. Overlap the two buckle straps (diag. 6A).
5. Insert both buckle straps until an audible
"click" is heard (diag. 6B). WARNING: never
insert only one strap in the buckle.
6. Tighten the child safety belts by pulling the
central adjustment belt (diag.9).
WARNING! Do not over-tighten the belts. If
you can insert your fi ngers between the harness
and your child's body, it means that they are
tightened correctly.
CARRY HANDLE POSITIONS
The carry handle of the child car seat can be
adjusted to 4-positions (diag. 10):
A. Position for car transport (WARNING: this is
All manuals and user guides at all-guides.com
26
the only position allowed during car transport).
X. Middle position: Never use this position
B. Position for carrying the child car seat by its
hand.
C. Position for using the child car seat as a baby
rocker or fi tting it to the Chicco stroller.
D. Position for using the child car seat as a baby chair.
To adjust the handle, press the buttons placed on
the handle simultaneously (diag. 11), rotate the
handle to the desired position until an audible
click is heard.
FITTING THE CHILD CAR SEAT INTO THE CAR
Please read this paragraph carefully: NECESSARY
REQUIREMENTS OF THE CAR SEAT AND
SAFETY BELT.
The child car seat, with or without base, must be
fi tted only rear-facing. WARNING! EXTREMELY
DANGEROUS: DO NOT FIT ON CAR SEATS
EQUIPPED WITH AIRBAGS, unless the airbags
have been de-activated.
WARNING! Never fi t the child car seat to a
car seat if it is only equipped with a 2 point car
safety belt safety belt.
FITTING THE CHILD CAR SEAT WITH BASE UNIT:
To fi t the child car seat with base unit to the car
seat, proceed as follows:
1. Release the child car seat from the base unit
by pulling the release handle (diag.12), and
simultaneously lift it by using the carry handle.
2. Place the base unit on the desired car seat, and
adjust it as shown in diag. 13, ensuring that it is
placed against the backrest of the car seat.
3. Pull the car seat belt and fasten it to the
buckle by passing the horizontal part through
the appropriate belt guides (diag.14).
4. Before fi tting the child car seat on to its base
unit, check that the securing device is closed
(diag. 15).
5. Place the child car seat on to its base unit in a
rear-facing position, and press downward until it
is secured (you will hear an audible click) (diag.
16).
6. Check that the child car seat has been
correctly secured to its base unit by trying to pull
it upward, both from the front and rear part.
7. Take the diagonal belt of the car, and pass it
through the belt guide located at the rear of the
child car seat's backrest diag. 17)...
WARNING: DURING
DIAGONAL BELT OF THE CAR MUST ALWAYS
BE IN THE POSITION SHOWN IN DIAG.
18A; NEVER USE THE CHILD CAR SEAT
WITHOUT PASSING THE BELT THROUGH THE
APPROPRIATE GUIDE:
TRANSPORT, THE