Assembly And Adjustment - DeWalt DE7464 Manual Del Usuario

20 Lock washers 10 mm
18 Flat washers 8 mm
22 Flat washers 10 mm
2 Allen screws 6 mm, M10 x 80
14 Cap head screws 8 x 20 mm
1 Instruction manual
1 Exploded drawing
• Check for damage to the tool, parts or accessories which may have
occurred during transport.
• Take the time to thoroughly read and understand this manual prior to
operation.
Description (fig. A1 & A2)
Your DE7464 ripping support system has been designed to extend the
capabilities of your D WALT woodworker's table saw.
E
Fig. A
1 Table
2 Rear rail
3 Front rail
4 Leg brace
5 Leg
6 Foot
7 Lower support rail

Assembly and adjustment

Also refer to the manual of the machine to be used with this
attachment.
Identifying the hardware parts (fig. B)
We recommend that you unpack and sort all hardware parts.
8 Allen key 6 mm
9 Torx wrench T50
10 Flat bracket
11 Torx bolt T50, M10 x 30
12 Coach bolt M8 x 20
13 Hex head bolt M10 x 25
14 Hex head bolt M10 x 35
15 Hex nut M8
16 Hex nut M10
17 Hex jamnut M10
18 Flat washer M8
19 Flat washer M10
20 Lock washer M8
21 Lock washer M10
22 Allen screw 6 mm, M10 x 80
23 Cap head screw 8 x 20 mm
Required and recommended tools
Apart from the tools included with the machine, the following tools are
required:
- Flat blade screwdriver
- Open end wrench 16 mm
- Open end wrench 13 mm
- Ruler
- Soft hammer (or regular hammer and block of wood)
The following tools would be helpful:
- Socket wrench 16 mm
- Socket wrench 13 mm
- Torx screwdriver T25
11
Always use the correct type and size of tool.
Preparations before assembling and mounting the attachment
In case the machine has already been set up, you will need to remove the
accessories and some of the parts including the associated hardware.
• Remove all accessories attached to the saw.
• If attached, remove the outfeed table.
• Remove the ripping fence, front rail, rear rail, motor cover and bottom plate.
In case the machine has not been set up yet, you will need to mount some
of the parts in advance.
• Unpack the saw.
• Mount the bevel adjuster.
• Mount the wrench hook.
Refer to the manual of the machine to perform these
preparations.
Mounting the feet to the legs (fig. C1 & C2)
Required hardware parts: 4 cap head screws (23), 4 flat washers (18),
4 lock washers (20), 4 nuts (15) (fig. C1).
• Place the foot (6) over the leg (5) as shown (fig. C2).
• Insert a cap head screw (23) into each of the holes in the foot and the leg.
• Place a flat washer (18), a lock washer (20) and a nut (15) onto the end
of each of the screws.
• Tighten the nuts ensuring that the foot is in the correct position.
• Repeat the procedure for the other leg.
Assembling the leg set (fig. C1 & C2)
Required hardware parts: 8 cap head screws (23), 8 flat washers (18),
8 lock washers (20), 8 nuts (15) (fig. C1).
• Hold the leg brace (4) against the leg (5) as shown (fig. C2).
• Insert a cap screw (23) into each of the holes in the leg and leg brace.
• Place a flat washer (18), a lock washer (20) and a nut (15) onto the end
of each of the screws.
• Tighten the nuts.
• Repeat the procedure for the other leg.
Assembling the table leveling hardware (fig. D1 - D3)
Required hardware parts: 2 Allen screws (22), 2 flat washers (19), 2 lock
washers (21), 4 jamnuts (17) (fig. D1).
• Insert an Allen screw (22) into each of the holes in the table (1) (fig. D2).
• Place a lock washer (21) and a nut (17) onto the end of each of the
screws.
• Carefully tighten the nuts.
Do not over-tighten the nuts to prevent damaging the table
board.
• Place the table (1) on the floor, surface upside down (fig. D3).
• Place a second nut (17) and a flat washer (19) onto onto the end of
each of the screws (22).
• Turn the nuts until the distance with the tightened nuts is approximately
7 mm.
Mounting the leg set to the table (fig. E1 & E2)
Required hardware parts: 2 cap head screws (23), 2 flat washers (18),
2 lock washers (20), 2 nuts (15), 2 flat washers (19), 2 lock washers (21),
2 jamnuts (17) (fig. E1).
• With the table surface upside down, place the leg set onto the leveling
hardware (fig. E2).
• Place a flat washer (19), a lock washer (21) and a nut (17) onto the end
of each of the screws (22).
• Tighten the nuts.
• Insert a cap head screw (23) into each of the holes in the sides of the legs.
E N G L I S H
en - 2