Publicidad

Idiomas disponibles

Idiomas disponibles

Please read and save these instructions
PACKAGE CONTENTS
Assembly and Installation
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
IMPORTANT SAFETY INSTRUCTIONS
CAUTION: Safe for outdoor operation
WARNING: Install in accordance with all local codes and ordinances.
Only for use with low voltage power units with a maximum output rating of 15V,
300W per secondary.
FOR LANDSCAPE LIGHTING SYSTEMS ONLY. OUTDOOR USE ONLY. THE DEVICE IS
ACCEPTED AS A COMPONENT OF A LANDSCAPE LIGHTING SYSTEM WHERE THE
SUITABILITY OF THE COMBINATION SHALL BE DETERMINED BY CSA OR LOCAL
INSPECTION AUTHORITIES HAVING JURISDICTION.
ETL LISTED UNDER MODEL # U000-1708
1
Attaching and installing the light
Assembly of the Light Fixture: Option 1 - Hidden wire
Find a location on the deck where you want to mount the light.
Using the template provided with the instruction manual, place it
over the deck and use a sharp object or a pen to mark where you
are going to put the screws (E) and drill the hole.
Drill a 1 in. hole where specified. Use the two (2) provided screws
(E) and screw them in the deck according to the template.
Pass the wire (C) and the connector (D) through the hole.
Mount the half brick light (B) on the screws (E).
Assembly of the Light Fixture: Option 2 – Flushmount
Find a location on the deck where you want to mount the light.
Using the template provided with the instruction manual, place it
over the deck and use a sharp object or a pen to mark where you
are going to put the screws (E).
Insert the screws (E).
Mount the half brick light (B) on the screws (E).
Assembly of the Light Fixture: Option 3 – Flushmount to cover older models
Remove the diffuser plate and the light component by unscrewing
the two thumbscrews (B)
Pass the wire in the hole
Secure the fixture onto the surface, covering the hole from the old
light fixture using the two screws from the old model (not included)
Install the diffuser and light component with the two thumbscrews (B)
Make sure the O-ring stays on the thumbscrews (B)
Option 1
Half brick
light (B)
Wire (C)
Connector (D)
Option 3
Screw (E)
B
A
Option 2
Screw (E)
Thumbscrew (B)
LOW VOLTAGE LED HALF BRICK STEP LIGHT
E
C
D
2
Connecting the wires
WARNING: The wire connector (D) contacts have sharp edges for piercing the
main low voltage cable. To avoid injury, do not touch the metal contacts.
WARNING: Risk of Electric Shock. Install all luminaires 10 ft. (3.05 m) or more
from a pool, spa or fountain.
CAUTION: The wire from the low voltage power unit shall be 12-16 AWG type
underground low Energy Circuit Cable or SPT2W.
IMPORTANT:
• Protect the wiring by routing it in close proximity to the light fitting, or next to a
• The landscape wire and connector can also be hidden under stone or buried
• Do not submerge fixture in water.
Place the wire connector (D) on opposite sides of the low
voltage cable (not included) where the fixture will be located.
Align and fit the main low voltage cable vertically to the slot of
the wire connector (D) as shown.
Press the wire connector (D) together until fully seated and
locked around the cable. Pre-set prongs will pierce the cable
insulation and establish contact. Turn on the power unit. If the
light fixture does not turn on, repeat the previous steps.
Once the clip-on connector (D) is in place, wrap it with
electrical tape for additional protection.
CAUTION BE CAREFUL! THE WIRE STABS ARE VERY SHARP!
After all fixtures are installed, turn on the transformer.
Use and Care Guide
Part
Description
A
Thumbscrews
B
Half brick light assembly
C
Wire
D
Connector
E
Screws
building structure such as a house or deck.
under grass at a maximum depth of 6" (15.24 cm).
D
Item #1001 492 878
Model #HD38682
Quantity
2
1
1
1
2

Publicidad

Tabla de contenido
loading

Resumen de contenidos para HAMPTON BAY HD38682

  • Página 1 Item #1001 492 878 Model #HD38682 Use and Care Guide LOW VOLTAGE LED HALF BRICK STEP LIGHT Please read and save these instructions PACKAGE CONTENTS Part Description Quantity Thumbscrews Half brick light assembly Wire Connector Screws Assembly and Installation INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS...
  • Página 2: Care And Cleaning

    Care and Cleaning □ Clean the fixture with a soft, dry cloth. □ Do not use any cleaners with chemicals, solvents or harsh abrasives. Troubleshooting Problem Possible cause Solution The fixture will not • There is no power. • Check that the power is on. light •...
  • Página 3 Template Screw here Screw here 2.36” Drill mark Drill 1” hole here...
  • Página 4 Núm. de artículo 1001 492 878 Núm. de modelo HD38682 Guía de uso y cuidado Por favor, lea y guarde estas instrucciones. LÁMPARA DE PELDAÑO DE MEDIASTA DE BAJO VOLTAJE LED CONTENIDO DEL PAQUETE Pieza Descripción Cantidad Tornillos pulgar Conjunto de la luz la mitad de ladrillo...
  • Página 5: Cuidado Y Limpieza

    Cuidado y limpieza Limpie el aparato con un paño suave y seco. o No utilice productos de limpieza con productos químicos, disolventes o abrasivos. o Resolución de fallas Problema Causa posible Solución El dispositivo no se • No hay poder. •...
  • Página 6 Modelo Tornillo aquí Tornillo aquí 2.36” Marca de taladro Taladro 1 “ agujero aquí...

Este manual también es adecuado para:

1001 492 878

Tabla de contenido