EAS ELECTRIC EMR185SW1 Manual De Instrucciones página 24

A
Hi Humidity
ó
B
ON/OFF
1. Keys
A. Hi Humidity: High Humidity Mode
B. ON/OFF: start up or shut down the system
C.?: increase temperature of the cooling chamber
D.Y: de crease temperature of the cooling chamber
2. Names of functions of display screen
1YHigh Humidity figure
2?Temperature region digitron
3flemperature (Y) figure
3. Display control
• Power on for the first time: all shines for three seconds with ringing of start bell.
Defaulting temperature of the cooling chamber is 5
• Normal operation display:
Temperature display region: when there is a failure, it will show failure codes by turn al a
priority order; without failure, il will show the set temperature.
High Humidity figure: shine when the system is under High Humidily Mode.
• Display control:
1YUnder the normal pattern, it will not shine any more after thirty seconds without opening and key
operation;
2YWhen the door is under open state, the display will shine all the time and it will stop shining thirty
seconds after the door is closed.
3YWhen a failure happens and it is within "Failure Code", the screen will shine for one time and
stop to shine after thirty seconds (if the buzzer has been ringing far a long lime, press any key
to cancel the failure bell);
4. U ser Mode operation
• Start-up and shutdown
Under start-up mode, press and hold ON/OFF key (B key) for three seconds, !he start bell will ring
and the system will be shut down immediately;
Under shutdown mode, press and hold ON/OFF key (B key) for three seconds, the start bell will
ring and the system will be started immediately.
Press ON/OFF key for three seconds to shul down !he system and !he display screen will not show
any more. Except ON/OFF key (B key), other keys will stop responding, and compressor, door
lamp and other loads will be shut down immediately;
Press ON/OFF key for three seconds to start up !he system. Befare starting, if the system is al
High Humidily Mode, !he High Humidily figure will shine, otherwise the system will only shine !he
set temperature and all loads will run !he mode having been set before shuldown.
V
3
2
º
C.
4
Function introduction
AII following functions must be worked under start state.
e
e High Humidity Mode
When the system is not at High Humidity Mode, press and hold Hi Humidity key (A key) for
three seconds to start the High Humidity Mode and High Humidity figure will be lit up.
D
When the system is al High Humidily Mode, press and hold Hi Humidily key (A key) for lhree
seconds to exit from lhe High Humidity Mode and High Humidity figure will not shine any
more.
When starting High Humidity Mode, cooling chamber will work under High Humidity state to
improve relative humidily of the air inside the cooling chamber.
• Set the temperature of the cooling chamber
Press temperature regulation keys Y (C key) and Y (D key) to set the temperature inside the
chamber and the set temperature will shine. T he selting range is belween 29 to BY (non­
periodic temperature regulation); it will exit from the system in five seconds and the setting
will take effect. (within five seconds after finishing the setting, press A key ar B key to affirm
the setting state manually and make the setting val id.)
5. llluminating lamp control
When open cooling chamber's door, cooling chamber's illuminating lamp will shine. When
close cooling chamber's door, cooling chamber's illuminating lamp will not shine any more.
6. Door-opening hint and door-opening alarming control
When open lhe door, lhe music will ring for one lime. lf refrigerator chamber door has
been open for 120 seconds, it will ring warning bell, and the bell will ring per 2 seconds till
the door is closed. Press any key to cancel the door-opening warning.
7. Power-interruption memory and initial power-up state
• When mee! power interruption, the refrigerator can memory operaling mode and state
before automalically; When power up, il will recover to lhe state before interruption and run
the mode having been set before interruption.
Y lnitial power-up state: the set temperature of cooling chamber is J5Y and the system is not
al High Humidity Mode.
• Memory: include set temperature of cooling chamber, "High Humidily" Mode and
cumulative working hours of compressor.
For example, if the system has a power failure under High Humidity state, it will continue to
work al "High Humidity" mode after recovery.
V.1
5
V.1