Publicidad
Idiomas disponibles
Idiomas disponibles
KIT COMPONENTS
• A) Radio trim panel • B) Radio brackets
A
B
The World's best kits.
®
Chevrolet Trax
KIT FEATURES
• ISO DDIN radio provision
• Painted to match factory finish
MetraOnline.com
2015-2016
© COPYRIGHT 2017 METRA ELECTRONICS CORPORATION
95-3017B
I N S TA L L AT I O N I N S T R U C T I O N S
TABLE OF CONTENTS
Dash Disassembly . .................................................2
Kit Assembly
– ISO DDIN radio provision . ...................................3
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: LC-GMRC-044 or AX-ADBOX2
and AX-ADGM04
Antenna Adapter: 40-EU55
Steering Wheel Control Interface: ASWC-1
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
• 9/32" socket wrench
CAUTION!
All accessories, switches, climate
controls panels, and especially air bag indicator
lights must be connected before cycling the
ignition. Also, do not remove the factory radio
with the key in the on position, or while the
vehicle is running.
REV. 9/19/17 INST95-3017B
Publicidad
Tabla de contenido
Manuales relacionados para Metra 95-3017B
Resumen de contenidos para Metra 95-3017B
- Página 1 Also, do not remove the factory radio with the key in the on position, or while the vehicle is running. The World’s best kits. MetraOnline.com ® © COPYRIGHT 2017 METRA ELECTRONICS CORPORATION REV. 9/19/17 INST95-3017B...
-
Página 2: Dash Disassembly
DASH DISASSEMBLY 1. Unclip and remove the panel surrounding the factory radio including the a/c vents. (Figure A) 2. Remove (4) 9/32” screws securing the radio chassis, then unplug and remove. (Figure B) 3. Remove (2) screws securing the a/c vents to the factory radio trim panel and keep for kit assembly. (Figure C) 4. Unclip and remove the (9) metal panel (Figure A) (Figure C) clips from the factory panel and keep them for kit assembly. 5. Unclip and remove the (2) small pockets on either side of the a/c vents and keep for kit assembly. (Figure D) Note: Remember the process when removing these pockets as you will need to reinstall them into the 99-3017B radio panel the same way. -
Página 3: Kit Assembly
KIT ASSEMBLY ISO DDIN radio provision 1. Clip the (2) small pockets into the 95- 3017B radio trim panel. 2. Attach the (9) metal panel clips to the 95-3017B radio trim panel. 3. Attach the a/c vents to the 95-3017B radio trim panel with the factory hardware. 4. Secure the radio brackets to the radio using the screws supplied with the radio. (Figure A) 5. Locate the factory wiring harness and antenna connector in the dash, and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra and/ (Figure A) or AXXESS. Test the radio for proper operation. 6. Secure the radio assembly into the dash and reassemble the dash in reverse order of disassembly using the 95-3017B radio trim panel. - Página 4 Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow. Metra recommends MECP certified technicians The World’s best kits. MetraOnline.com ® © COPYRIGHT 2017 METRA ELECTRONICS CORPORATION REV. 9/19/17 INST95-3017B...
- Página 5 Además, no quite el radio de fábrica con la llave en la posición o de encendido ni con el vehículo funcionando. The World’s best kits. MetraOnline.com ® © COPYRIGHT 2017 METRA ELECTRONICS CORPORATION REV. 9/19/17 INST95-3017B...
-
Página 6: Desmontaje Del Tablero
DESMONTAJE DEL TABLERO 1. Desenganche y quite el panel que rodea el radio de fábrica, incluyendo las rejillas del aire acondicionado. (Figura A) 2. Quite los (4) tornillos de 9/32” que sujetan el chasís del radio, y luego desconecte y quite. (Figura B) 3. Quite los (2) tornillos que sujetan las rejillas de aire acondicionado al panel de la moldura del radio de fábrica y guárdelos para el ensamble del kit. (Figura C) (Figura A) (Figura C) 4. Desenganche y quite los (9) ganchos para panel de metal del panel de fábrica y guárdelos para el ensamble del kit. 5. Desenganche y quite las (2) cavidades pequeñas de cada lado de las rejillas de aire acondicionado y guárdelas para el ensamble del kit. (Figura D) Nota: Recuerde el proceso cuando quite estas cavidades, ya que deberá reinstalarlas en el panel de radio 99- (Figura B) (Figura D) -
Página 7: Ensamble Del Kit
ENSAMBLE DEL KIT Provisión de radio ISO DDIN 1. Enganche las (2) cavidades pequeñas en el panel de la moldura del radio 95-3017B. 2. Coloque los (9) ganchos para panel de metal en el panel de la moldura del radio 95-303017B. 3. Coloque las rejillas del aire acondicionado en panel de la moldura del radio 95-3017B usando la tornillería de fábrica. 4. Sujete los soportes del radio al radio usando los tornillos que vienen con el radio. (Figura A) 5. Localice el arnés de cableado de fábrica... - Página 8 800-354-6782 para obtener más información y avance hacia un futuro mejor. Metra recomienda técnicos con certificación del Programa de Certificación en Electrónica Móvil (Mobile Electronics Certification Program, MECP). The World’s best kits. MetraOnline.com ® © COPYRIGHT 2017 METRA ELECTRONICS CORPORATION REV. 9/19/17 INST95-3017B...