Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
KIT COMPONENTS
• A) Radio trim panel • B) Radio brackets
A
B
Metra. The World's Best Kits.
®
GM Small trucks/SUV's
MetraOnline.com
Visit
for more detailed information about the product and up-to-date vehicle
specific applications
KIT FEATURES
• ISO DDIN radio provision
APPLICATIONS
Chevrolet S-10 Blazer 1998-2002*
Chevrolet S-10 Pickup 1998-2002*
GMC Jimmy (a.k.a. Jimmy Envoy)
1998-2001
MetraOnline.com
1998-2002
GMC Sonoma 1998-2002*
Isuzu Hombre 1998-2000
* Only for early 2002 models denoted by a
DIN and a half size radio
© COPYRIGHT 2021 METRA ELECTRONICS CORPORATION
95-3027
I N S TA L L AT I O N I N S T R U C T I O N S
TABLE OF CONTENTS
Dash Disassembly ..................................................2
Kit Preparation ....................................................2-3
Kit Assembly ..........................................................3
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: 70-1858
Antenna Adapter: 40-GM10
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
• 9/32" socket wrench • cutting tool • Scribe tool
Attention!
With the key out of the ignition,
disconnect the negative battery terminal
before installing this product. Ensure that all
installation connections are secure before
cycling the ignition to test this product.
REV. 7/15/21 INST95-3027
Publicidad
Tabla de contenido
Manuales relacionados para Metra 95-3027
Resumen de contenidos para Metra 95-3027
- Página 1 Ensure that all installation connections are secure before cycling the ignition to test this product. Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2021 METRA ELECTRONICS CORPORATION REV. 7/15/21 INST95-3027...
-
Página 2: Dash Disassembly
DASH DISASSEMBLY KIT PREPARATION 1. Remove (2) 9/32” screws securing the 1. Place the radio trim panel over the driver’s side knee bolster to the dash. factory dashboard trim panel. (Figure A) (Figure A) 2. Using a scribe tool, score the area in the 2. -
Página 3: Kit Assembly
(Figure C) the radio. Metra recommends using 5. Cut the sub-dash to allow room for the the proper mating adapter from Metra radio assembly. (Figure D) and/or Axxess. Test the radio for proper operation. - Página 4 Log onto www.installerinstitute.edu or call 386-672-5771 for more information and take steps toward a better tomorrow. Metra recommends MECP certified technicians Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2021 METRA ELECTRONICS CORPORATION REV. 7/15/21 INST95-3027...
- Página 5 Al probar el equipo del mercado de accesorios, asegúrese de que todo el equipo de fábrica esté conectado antes de encender el llave de encendido. Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2021 METRA ELECTRONICS CORPORATION REV. 7/15/21 INST95-3027...
-
Página 6: Desmontaje Del Tablero
DESMONTAJE DEL TABLERO PREPARACIÓN DEL KIT 1. Quite los (2) tornillos de 9/32” que 1. Coloque el panel de moldura del radio fijan el soporte lateral para rodillas del encima del panel de moldura del tablero conductor al tablero. de fábrica. (Figura A) 2. -
Página 7: Ensamble Del Kit
(Figura C) el uso de adaptadores de acoplamiento 5. Corte el sub-tablero para contar con adecuados de Metra o de Axxess. Pruebe espacio para el ensamble del radio. el radio para asegurarse de que (Figura D) funciona bien. - Página 8 Log onto www.installerinstitute.edu or call 386-672-5771 for more information and take steps toward a better tomorrow. Metra recomienda MECP técnicos certificados Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2021 METRA ELECTRONICS CORPORATION REV. 7/15/21 INST95-3027...