Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Installation instructions for part 95-3017B
Chevrolet Trax 2015-up
KIT FEATURES
• ISO DDIN radio provision
• Painted to match factory finish
KIT COMPONENTS
• A) Radio trim panel • B) Radio brackets
A
B
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: • LC-GMRC-044 or AX-ADBOX2 and AX-ADGM04
Antenna Adapter: • 40-EU55
METRA. The World's best kits.
95-3017B
metraonline.com
™
Table of Contents
Dash Disassembly ................................................. 2
Kit Assembly
– ISO DDIN radio provision ...................................... 3
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
• Socket wrench
CAUTION: Metra recommends disconnecting the negative battery
terminal before beginning any installation, unless the vehicle
manufacturer recommends against so. Please check with your
local Dealership for more information. All accessories, switches,
climate controls panels, and especially air bag indicator lights
must be connected before reconnecting the battery or cycling
the ignition. Also, do not remove the factory radio with the key
in the on position, or the vehicle running. It would be best to
remove the key from the ignition and then wait a few seconds
before removing the factory radio.
© COPYRIGHT 2015 METRA ELECTRONICS CORPORATION
Publicidad
Manuales relacionados para Metra 95-3017B
Resumen de contenidos para Metra 95-3017B
- Página 1 KIT COMPONENTS • A) Radio trim panel • B) Radio brackets • Socket wrench CAUTION: Metra recommends disconnecting the negative battery terminal before beginning any installation, unless the vehicle manufacturer recommends against so. Please check with your local Dealership for more information. All accessories, switches,...
- Página 2 95-3017B Dash Disassembly 1. Unclip and remove the panel surrounding the factory radio including the a/c vents. (Figure A) 2. Remove (4) 9/32” screws securing the radio chassis. (Figure B) 3. Remove (2) screws securing the a/c vents to the factory radio trim panel and keep for kit assembly.
- Página 3 95-3017B radio trim panel. AXXESS. Re-connect the negative 3. Attach the a/c vents to the battery terminal and test the radio 95-3017B radio trim panel with the for proper operation. factory hardware. 6. Mount the new radio assembly into 4.
- Página 4 Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow. Metra recommends MECP certified technicians METRA. The World’s best kits. metraonline.com ™ © COPYRIGHT 2015 METRA ELECTRONICS CORPORATION...
- Página 5 • A) Panel de moldura del radio • B) Soportes del radio • Destornillador Phillips • Llave de tubo PRECAUCIÓN: Metra recomienda desconectar la terminal negativa de la batería antes de iniciar cualquier instalación, a menos que el fabricante del vehículo recomiende lo contrario.
- Página 6 95-3017 Desmontaje del tablero 1. Desenganche y quite el panel que rodea el radio de fábrica, incluyendo las rejillas del aire acondicionado. (Figura A) 2. Quite los (4) tornillos de 9/32” que sujetan el chasís del radio. (Figura B) 3. Quite los (2) tornillos que sujetan las rejillas de aire acondicionado al panel de la moldura del radio de fábrica y guárdelos para el ensamble del kit.
- Página 7 1. Enganche las (2) cavidades antena en el tablero y realice pequeñas en el panel de la todas las conexiones necesarias moldura del radio 95-3017B. al radio. Metra recomienda el uso de adaptadores adecuados 2. Coloque los (9) ganchos para panel...
- Página 8 800-354-6782 para obtener más información y avance toward a better tomorrow. hacia un futuro mejor. Metra recomienda técnicos con certificación del Programa de Certificación en Electrónica Móvil (Mobile Electronics Certification Program, MECP). METRA. The World’s best kits. 1-800-221-0932 metraonline.com ™ © COPYRIGHT 2015 METRA ELECTRONICS CORPORATION...