1. Manuales
  2. Marcas
  3. Metra Manuales
  4. Accesorios de Automóviles
  5. 95-3009
  6. Instrucciones de instalación

Metra 95-3009 Instrucciones De Instalación

Ocultar thumbs
1
2
3
4
5
6
7
8
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Descargar este manual
KIT COMPONENTS
• A) Radio trim panel • B) Radio brackets • C) (1) #10 x 1/2" Phillips screw
A
Metra. The World's Best Kits.
®
Chevrolet Camaro 1993-1996
KIT FEATURES
• ISO DDIN radio provision
• Replacement trim panel is textured to match the factory finish
B
MetraOnline.com
C
© COPYRIGHT 2018 METRA ELECTRONICS CORPORATION
95-3009
I N S TA L L AT I O N I N S T R U C T I O N S
TABLE OF CONTENTS
Dash Disassembly . .................................................2
Kit Preparation . ......................................................2
Kit Assembly ..........................................................3
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: 70-1858
Antenna Adapter: 40-GM10
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
• 9/32", 10mm Socket wrench • Cutting tool
CAUTION!
All accessories, switches, climate
controls panels, and especially air bag indicator
lights must be connected before cycling the
ignition. Also, do not remove the factory radio
with the key in the on position, or while the
vehicle is running.
REV. 1/4/18 INST95-3009

Publicidad

Tabla de contenido
loading

Manuales relacionados para Metra 95-3009

Resumen de contenidos para Metra 95-3009

  • Página 1 Also, do not remove the factory radio with the key in the on position, or while the vehicle is running. Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 1/4/18 INST95-3009...

  • Página 2: Dash Disassembly

    DASH DISASSEMBLY KIT PREPARATION 1. Remove (2) Phillips screws from the top 1. Using a cutting tool, remove the section of the driver’s side knee bolster. of subdash indicated. (Figure A) 2. Remove (2) 9/32” screws from the Continue to Kit Assembly bottom of the knee bolster. 3. Open the glove box, remove (3) 9/32” screws exposed on the right edge of the radio trim bezel and remove the bezel. (Figure A) 4. Remove (2) 9/32” screws securing the left side of the factory radio and (1) (Figure A) (Figure A) 10mm nut securing the right. 5. Slide the radio from the dash and disconnect the wiring. Continue to Kit Preparation 1.800.221.0932 MetraOnline.com...

  • Página 3: Kit Assembly

    KIT ASSEMBLY ISO DDIN radio provision 1. Attach the radio brackets to the radio using the screws supplied with the radio. (Figure A) 2. Locate the factory wiring harness and connector in the dash and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra. Test the radio for proper operation. 3. Secure the completed assembly into the dash. Use the factory screws for the drivers side radio bracket and (1) #10 x 1/2” Phillips screw provided into the passenger side of the radio bracket. (Figure A) 4. Reassemble the dash in reverse order of disassembly, using the radio trim panel instead of the factory panel. REV. 1/4/2018 INST95-3009...
  • Página 4 Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow. Metra recommends MECP certified technicians Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2017 METRA ELECTRONICS CORPORATION REV. 1/4/18 INST95-3009...
  • Página 5 Además, no quite el radio de fábrica con la llave en la posición o de encendido ni con el vehículo funcionando. The World’s best kits. MetraOnline.com ® © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 1/4/18 INST95-3009...

  • Página 6: Desmontaje Del Tablero

    DESMONTAJE DEL TABLERO PREPARACIÓN DEL KIT 1. Quite los (2) tornillos Phillips de la parte 1. Usando una herramienta de corte, quite de arriba del lado del chofer. (Figura A) la sección de subdash indicada. (Figura A) 2. Quite los (2) tornillos de 9/32” de la parte de abajo del protector de la rodilla.

  • Página 7: Ensamble Del Kit

    Metra recomienda el uso de adaptadores adecuados de acoplamiento de Metra. Pruebe el radio para verificar si funciona bien. 3. Asegure el conjunto completo en el tablero. Use los tornillos de fábrica...
  • Página 8 800-354-6782 for more information and take steps www.installerinstitute.com o llame al toward a better tomorrow. 800-354-6782 para obtener más información y avance hacia un futuro mejor. Metra recomienda MECP Técnicos certificados The World’s best kits. MetraOnline.com ® © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 1/4/18 INST95-3009...

Tabla de contenido