Tabla de contenido
Publicidad
12 | English
(10)
Drill hole nozzle
(11)
Dust collection tube
(12)
Bayonet lock
(13)
Recess for dust collection tube
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical Data
Cordless blower
Article number
No-load speed
Air speed, max.
Air volume
Weight according to EPTA-
Procedure 01:2014
Recommended ambient tem-
perature during charging
Permitted ambient temperat-
B)
ure during operation
and
during storage
Recommended batteries
Recommended chargers
Operating time per battery charge
– Blower level I
– Blower level II
A) Depends on battery in use
B) Limited performance at temperatures <0 °C
Technical data determined using the battery that comes with the
product.
Noise/Vibration Information
Noise emission values determined according to
EN 62841-1.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 82 dB(A); sound power level
93 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
Vibration total values a
(triax vector sum) and uncertainty K
h
determined according to EN 62841-1:
2
2
a
< 2,5 m/s
, K = 1,5 m/s
,
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
1 609 92A 4YD | (05.09.2019)
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
GBL 18V-120
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
3 601 JF5 1..
1
min
17,000
Assembly
m/s
75
3
m
/min
2.0
Battery Charging
A)
kg
1.4–2.4
u
°C
0 to +45
Note: The battery is supplied partially charged. To ensure
°C
–20 to +50
full battery capacity, fully charge the battery in the charger
before using your tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
GBA 18V...
does not damage the battery.
ProCORE 18V...
The lithium-ion battery is protected against deep discharge
GAL 18...
by Electronic Cell Protection (ECP). A protective circuit
GAX 18...
switches the power tool off when the battery is drained.
GAL 36...
u
min/Ah
9
min/Ah
5
Removing the battery (see figures A1 –A2)
The battery (3) is equipped with two locking levels to pre-
vent the battery from falling out if the battery release but-
ton (7) is pressed unintentionally. As long as the battery is
inserted in the power tool, it is held in position by means of a
spring.
– To remove the battery (3), press the release button (7)
Follow the instructions on correct disposal.
Fitting the blower accessories (see figures B1 –
B3)
u
See the illustration for ways of combining the different
blower accessories.
– Insert the bayonet lock (12) of the accessory firmly into
– Turn the bayonet lock a quarter turn clockwise.
Use only the chargers listed in the technical data. Only
these chargers are matched to the lithium-ion battery of
your power tool.
Do not continue to press the on/off switch after the
tool has been automatically switched off. This can
damage the battery.
and pull the battery upwards and out of the power tool.
Do not use force to do this.
Remove the battery before cleaning or performing
maintenance work on the power tool, before making
tool adjustments, changing accessories or storing the
power tool. This safety measure prevents the power tool
from being started accidentally.
the recesses (8) of the motor housing or into the re-
cesses(8) of the extension tube (9).
Bosch Power Tools
Publicidad
Tabla de contenido
