Risk of malfunction & Damage: You must turn
the ON/OFF switch to OFF before selecting
INSIDE/WALL thermostat.
Selecting Inside Thermostat:
1.Turn the ON/OFF switch to OFF position, and then turn the
thermostat rocker switch to INSIDE THERMOSTAT as
indicated below:
2.Turn the ON/OFF switch to ON position again, the heater will
work on the inside thermostat mode.
Selecting Wall Thermostat:
1.Turn the ON/OFF switch to OFF position, and then turn the
thermostat rocker switch to WALL THERMOSTAT as indicated
below:
2.Turn the ON/OFF switch to ON position, the heater will work
on the wall thermostat mode.
Risk of malfunction & Damage: You can not change the
INSIDE/WALL THERMOSTAT when the heater is
running, you must turn the ON/OFF switch to OFF and
then select the INSIDE/WALL thermostat mode.
Remote Control
Insert the batteries into the remote control as shown below:
NOTE: Remove the batteries if the remote control is not to be
used for a month or more. Batteries left in the remote may
leak and cause damage.
DO NOT MIX OLD AND NEW BATTERIES! DO NOT MIX
ALKALINE, STANDARD (CARBON-ZINC) OR RECHARGE-
ABLE (NICKEL-CADMIUM) BATTERIES!
Horizontal Downflow Unit Heater
With Remote Control
Turning The Heater On
To turn the heater ON, switch on the circuit breaker, press the
ON/OFF rocker switch to ON position, press the POWER button
on the remote, the power indicator will turn on and display the
room temperature.
Setting The Temperature (with the remote
control)
Note: You need to select the thermostat to INSIDE
THERMOSTAT and then set the desired temperature:
Press the + button until the numeric temperature starts flashing.
Press button again to increase the temperature or the – button
to decrease the temperature.
The heater will run on heating when the room temperature is
equal to or lower than the setting temperature - 2℉, and will
turn off when the room temperature is equal to or greater than
the setting temperature+2℉.
The factory setting temperature is 70℉, if the room temperature
is lower or equal to 68℉, the heater will run out heating and will
turn off when the room temperature is higher or equal to 72℉.
Note: If you set the thermostat switch to WALL
THERMOSTAT, press the + and - button cannot set the
temperature, the heater will run in ON or OFF heating
according the wall thermostat setting temperature.
Setting HIGH/LOW Heating Mode
When the heater is running, press the MODE button to set the
heater to run on HIGH or LOW heating.
HIGH heating: 7500W
LOW heating: 4700W
Note: You can not set the HIGH/LOW mode when the room
temperature is equal to or greater than the set temperature
+2℉, because the heater is OFF.
Setting The Timer (with the remote control)
1.Press the TIMER button until Set Time starts flashing.
The default value is 3 hours.
2.Press the "+" button to increase the set time or the "–" button
to decrease the set time. The timer can be set from 1 to 12
hours. The timer will set and execute after the LED display
stops flashing. The heater will shut OFF automatically when
the set time is reached.
3.To turn the timer OFF, press the TIMER button, and then
pressing the "–" button to set the time to 0. The timer feature
will turn off when the LED stops flashing.
Turning The Heater Off
To turn off the heater, switch off the circuit breaker. The circuit
breaker serves as the power source for the heater.
This heater includes a visual alarm to warn that parts of the
heater are getting excessively hot. If the alarm flashes, immedi-
ately turn the heater OFF and inspect for any objects on or ad-
jacent to the heater that may cause high temperatures. DO
NOT OPERATE THE HEATER WITH THE ALARM FLASHING.
To reset the heater, switch the circuit breaker OFF. Wait five to
ten minutes for the heater to cool down before turning the
heater on again.
6
User's Manual