Publicidad
Idiomas disponibles
Idiomas disponibles
LOGDATE:
It displays the time and date at last time
Barometer Data was cleared.
MAX:
It displays the maximum absolute air
pressure during the period measured,
time and date.
MIN:
It displays the minimum absolute air
pressure during the period measured,
time and date.
NOTE: The barometer measures changes
in air pressure, which you can then apply
to your own weather predictions, it is not
intended for use as a precision instru-
ment in official weather prediction or
reporting application. If you remain at the
same altitude, changes in air pressure
help you to predict changes in weather
conditions.
Sudden temperature changes can affect
barometer sensor readings.
1. Press S3 button to select
BAROMETER mode.
2. The latest sea level pressure will
be displayed in numeric and graphic
formats.
TO SET UP THE BAROMETER
1. In BAROMETER mode, press and
hold S4 button. The message "Sea
-Lv" will be displayed.
2. Press S1/S2 button to select among
sea level pressure setting mode
(Sea-Lv) or units setting mode
(UNITS).
3. Press S3 button once to enter into
each setting mode. Press S3 button
again to return to the mode
selection screen.
4. In sea level pressure setting mode,
press S1/S2 button to set the sea
level pressure digits.
5. In units setting mode, press S1/S2
button to toggle between blinking
mbar (millibar) and inHg (inch of
Mercury).
6. When finished making all the settings,
press S4 button to return to
BAROMETER mode.
TO SHOW THE LOG DATE AND TIME
1. In BAROMETER mode, press S2
button to display log date and time.
2. Press S3 button or leave the watch
idle for approximately 5 seconds to
return to BAROMETER mode.
NOTE: The sea level barometric pressure
(SLP) data can be gathered from relevant
websites, weather stations or other
sources of this type of information. For
example, US residents can gather the
SLP data from National Weather Service
(http://www.nws.noaa.gov/) or an FAA
Flight Service Station.
TO CLEAR THE DATA
1. In BAROMETER mode press and hold
S2 button for approximately 3 seconds
to clear all statistic data and graphic
data.
Before measuring pressure you have to
key in and reset certain data in the initial
setting and clear data every time, in order
to have a more accurate measurement.
All manuals and user guides at all-guides.com
BAROMETER mode
Initial setting (key in the
"SET-Lv" for setting sea
level pressure)
Data clear
Measuring can start
NOTE: In the bar chart, after clearing
the data, new data will be updated after
2 seconds and another will be taken in
an hour.
TO VIEW BAROMETER AND OTHER
INFORMATION
1. In BAROMETER mode, press S1
button to select displaying the data
of sea level pressure (SEA-Lv), sea
level pressure change per hour
(dP/dt) or time (TIME).
2. Press S1 button continuously to
view data of Sea level pressure,
dP/dt (sea level pressure change
per hour) and Time.
3. After showing the individual data at
the bottom for approximately 2
seconds, the data in trend (graphic)
format will be displayed at the top.
TO VIEW DATA IN DETAIL
1. In BAROMETER mode, press S4
button once. The message "VIEW
DATA" will be displayed.
2. After approximately 2 seconds or by
pressing S1/S2 button, the message
"MAX" will be displayed.
3. Press S1 button to select displaying
the data of maximum absolute
pressure (MAX), minimum absolute
pressure (MIN) or the statistic and
graphic data recorded. Press S2
button to cycle the selection
backward.
4. When displaying maximum
absolute pressure, minimum
absolute pressure and the individual
statistic and graphic data recorded,
the corresponding log time and date
will be swapping in every 2 seconds.
5. Press S3/S4 button to return to
BAROMETER mode.
NOTE: Because the barometer and
altimeter both use air pressure, only one
of these modes may be activated at a
time. Therefore, you will have to activate
the barometer separately for use.
TO USE THE CHRONOGRAPH
1. Press S3 button to select
CHRONOGRAPH mode.
2. The chronograph will then be
displayed in its current state – reset,
running or stopped.
3. To resume a counting, press S1
button to resume from where it left
off.
4. To start a new counting, reset the
chronograph to zero first.
Press S2 button to stop counting,
then press and hold S2 button for
approximately 3 seconds to reset the
counter to zero.
FOR THE MEASUREMENT OF ELAPSED
TIME
In CHRONOGRAPH mode,
1. Press S1 button to start counting.
2. To stop counting, press S2 button.
Press S1 button to resume from
where if left off.
3. To reset to zero, press S2 button to
stop counting, then press and hold
S2 button for approximately 3 seconds
to reset the counter to zero.
FOR THE MEASUREMENT OF SPLIT TIME
AND LAP TIME
In CHRONOGRAPH mode,
1. Press S1 button to start counting.
2. While the chronograph is running,
press S1 button once to register a
lap. Both the split time and lap time
will be displayed.
After 3 seconds, the currently
accumulated split time and lap time
will be displayed.
3. Repeat the last step until all the
laps have been registered.
4. To stop counting, press S2 button.
Press S1 button to resume from
where if left off.
5. To reset to zero, press S2 button to
stop counting, then press and hold
S2 button for approximately 3 seconds
to reset the counter to zero.
NOTE: The watch can record up to a
maximum of 99 laps. During a measure-
ment of split time and lap time, the
message "FULL" will be displayed when
the memory is full.
TO USE THE RECALL FUNCTION
1. After the measurement of split
time, press S4 button to select
RECALL mode when the
chronograph is stopped.
2. After 2 seconds or by pressing
S1/S2 button, the sum of time of all
lap counting (TOTAL) will be
displayed.
3. Press S1/S2 button to select
displaying the sum of time of all lap
counting (TOTAL), best lap (BEST),
average time (AVERAGE) or
individual lap record (LAP-XX).
4. Press S4 button to return to
CHRONOGRAPH mode or press S3
button to return to TIME mode.
NOTE: The lap record(s) will be cleared
when chronograph is reset.
NOTE: The average time (AVERAGE) is
the total time of all lap counting over the
number of lap count.
TO SET THE TIMER
CHRO or Lap#
Split time
1. Press S3 button to select TIMER
Lap time
mode.
2. Press and hold S4 button for approxi-
mately 3 seconds, the second digits
will blink.
3. Press S1/S2 button to set the
second digits. Holding down the
button will speed up the process.
4. Press S3 button, the minute digits
will blink.
5. Press S1/S2 button to set the
minute digits.
6. Press S3 button, the hour digits will
blink.
7. Press S1/S2 button to set the hour
digits.
8. Press S3 button, the mode selection
will blink.
9. Press S1/S2 to select among
countdown stop mode (Cd-STOP),
countdown up mode (Cd-UP) and
ENGLISH
Countdown time
Mode
Publicidad
