Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
has raised the air tank pressure above that required at the
air outlet.
Drain Valve
: The drain valve is located at the base of
8
the air tank and is used to drain condensation at the end of
each use.
Check Valve
: When the air compressor is operating,
9
the check valve is "open", allowing compressed air to enter
the air tank. When the air compressor reaches "cut-out"
pressure, the check valve "closes", allowing air pressure to
remain inside the air tank.
Motor Overload Protector (not shown): The motor has
a thermal overload protector. If the motor overheats for any
reason, the overload protector will shut off the motor. The
motor must be allowed to cool down before restarting. To
restart:
1. Set the Auto On/Off switch to "Off".
2. Remove the battery.
3. Allow the motor to cool.
4. Replace the battery.
5. Set the Auto On/Off switch to "Auto On" position.
Quick-Connect Coupler
accepts industrial quick connect plugs.
How to Use Your Unit (Fig. C)
How to Stop
1. Set the Auto On/Off switch
2. Remove battery when not in use.
Before Starting
WARNING: Do not operate this unit until you read
this instruction manual for safety, operation and
maintenance instructions.
Before Each Start-Up
1. Remove battery. (Refer to installing and Removing
the Battery Pack)
2. Set the Auto On/Off switch
3. Turn the regulator dial
outlet pressure to zero.
4. Attach hose and accessories.
WARNING: Risk of unsafe operation. Firmly grasp
air hose in hand when installing or disconnecting
to prevent hose whip.
WARNING: Risk of unsafe operation. Do not use
damaged or worn accessories.
nOTE: The hose or accessory will require a quick connect
plug if the air outlet is equipped with a quick connect
coupler
10
.
WARNING: Risk of Bursting. Too much air pressure
causes a hazardous risk of bursting. Check the
manufacturer's maximum pressure rating for air tools
and accessories. The regulator outlet pressure must
never exceed the maximum pressure rating.
NOTICE: Risk of property damage. Compressed air
from the unit may contain wa ter condensation and
oil mist. Do not spray un fil tered air at an item that
could be damaged by moisture. Some air tools and
: The quick connect body
10
1
to "Off".
to "Off".
1
7
counterclockwise to set the
accessories may require filtered air. Read the in struc-
tions for the air tools and accessories.
How to Start
1. Install the battery into the tool.
2. Set the Auto On/Off switch
tank pressure to build. Motor will stop when tank
pressure reaches "cut-out" pressure.
3. Turn regulator dial
7
stop when desired pressure is reached.
WARNING: Risk of unsafe operation. If any
unusual noise or vibration is noticed, stop the
compressor immediately and have it checked by
a trained service technician.
WARNING: Ensure the regulator is set to a pressure
lower than the maximum operating pressure of
the tool.
The compressor is ready for use.
Fig. C
7
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.
Customer Responsibilities
Before each
Check Safety Valve
Drain Tank
Remove tank from service
*** For more information, call our Customer Care Center at
1–888–331–4569
WARNING: Risk of unsafe operation. Unit cycles
automatically when power is on.
When performing maintenance, you may be exposed
to voltage sources, compressed air, or moving parts.
Personal injuries can occur. Before performing any
maintenance or repair, disconnect power source from
the compressor and bleed off all air pressure.
nOTE: See Operation section for the location of controls.
1
to "Auto On" and allow
clockwise to increase pressure and
1
6
4
10
Daily or after
See tank
use
each use
warning label
X
X
English
X
***
9
Publicidad
Tabla de contenido
