Andis AGR+ Manual Del Usuario página 4

F G
I
J
L
M
OIL
OIL OIL
O
Q
CORRECT
6
H
K
N
P
R
INCORRECT
BLADE TEMPERATURE
Due to the high speed nature of Andis clippers, please check for blade heat often, especially on close
cutting blades. If blades are too hot, dip the blades only into Andis Blade Care Plus or apply Andis Cool
Care Plus and then Andis Clipper Oil. If you have a detachable blade unit, you can change your blade in
order to maintain a comfortable temperature; using multiple blades of the same size is popular among
groomers.
CARE AND SERVICING OF YOUR ANDIS CLIPPER BLADES
Blades should be oiled before, during, and after each use. If your clipper blades leave streaks or slow
down, it's a sure sign blades need oil. Place a few drops of oil on the front and side of the cutter blades
(Figure L). Wipe excess oil off blades with a soft, dry cloth. Spray lubricants contain insufficient oil for
good lubrication, but are an excellent clipper blade coolant. Always replace broken or nicked blades to
prevent injury. You can clean the excess hair from your blades by using a small brush or worn out
toothbrush. To clean the blades, we suggest to immerse the blades only into a shallow pan of Andis
Clipper Oil, while the clipper is running. Any excess hair and dirt that has accumulated between the
blades should come out. After cleaning, turn your clipper off and dry blades with a clean, dry cloth and
start clipping again. If upon cleaning your blades you find that the blades will still not cut, there may be a
few fine pieces of hair trapped between the upper and lower blade. If this happens, you will need to
snap the blade off the clipper. Proceed to slide the upper blade to one side, without loosening the
tension spring or moving the upper blade completely out from under the tension spring (See Figure M for
position of blade). Wipe the surface between the blades clean with a dry cloth, then place a drop of
clipper oil where the upper and lower blades meet and also in the guide slot of the tension spring
(Figure M). Now slide the upper blade to the opposite side of the lower blade and repeat this process.
After completing this procedure, slide the upper blade, centering it over the lower blade. Handle or
store your Andis clipper with the blades down so excess oil will not run into the clipper case.
CHANGING THE BLADE DRIVE ASSEMBLY
If your clipper blades no longer cut properly (be sure to try more than one blade, since the blade
currently being used may be dull), it could be that your blade drive assembly needs replacement.
TO CHANGE THE BLADE DRIVE ASSEMBLY:
1. Remove blade set (Figure I).
2. Remove drive cap (Figure N).
3. Remove blade drive mounting screws (Figure O).
4. NOTE: Before removing blade drive assembly, note the way it is positioned (this will help you in
reassembly). Remove blade drive assembly (Figure P).
5. Drive bearing should be at its lowest position, if not, move it with your finger to lowest position
(Figures Q & R).
6. Put on new drive assembly, align screw holes and press down (Figure P).
7. Reassemble blade drive by replacing mounting screws, turning just until snug (Figure O). DO NOT
OVERTIGHTEN.
8. Replace drive cap (Figure N).
9. Replace blade (Figure K).
BLADE & CLIPPER/TRIMMER REPAIR SERVICE
When the blades of your Andis clipper/trimmer become dull after repeated use, it is advised to purchase
a new set of blades available through your Andis supplier. Some blade sets can be resharpened – contact
your Andis supplier or the Andis Company for information on resharpening. If you wish your clipper/
trimmer to be serviced as well, contact your Andis supplier. If you have a problem contacting your Andis
supplier, contact the Andis Company customer service department 1-262-884-2600 (USA) or email at
info@andisco.com. To find an Andis Authorized Service Station near you log on to www.andis.com
or contact our customer service department by phone at 1-262-884-2600 (USA), or by email at
info@andisco.com.
CORRECT DISPOSAL OF THIS PRODUCT
This marking indicates that this product should not be disposed with other household wastes
throughout the EU. To prevent possible harm to the environment or human health from
uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material
resources. To return your used device, please use the return and collection systems or contact
the retailer where the product was purchased. They can take this product for environmental safe
recycling.
CAUTION: Never handle your Andis clipper while you are operating a water faucet and never hold your
clipper under a water faucet or in water. There is danger of electrical shock and damage to your clipper.
ANDIS COMPANY will not be responsible in case of injury due to this carelessness.
7