Orbea GAIN HYDRO Manual Tecnico página 10

18 | OR B EA
06 X35 SYSTE M
OPERATIO N
CH A RGING T HE BAT T ERY
To charge the battery, connect the X35 charger to a power
outlet and check that the LED on the charger turns green.
Connect the X35 charger to the ebike's charging port,
aligning the arrows and securing the connection by turn-
ing the safety ring clockwise. The LED on the charger will
turn red. It will turn green once the battery is fully charged.
While the battery is charging, the Iwoc One light will
fade in and out, showing the color code for the current
battery level. Once the battery is fully charged, the Iwoc
One charging indicator will turn white. Turn the safety
ring counterclockwise and detach the charger from the
charging port.
>25% >50%
<25%
<50% <75%
BATTERY LEVEL VISUALIZATION
(DURING USE)
While the bike is on, the Iwoc One and Trio will display the
current battery level with the following color codes:
· SOLID WHITE: >75% battery charge.
· SOLID GREEN: 75%-50% battery charge.
· SOLID ORANGE: 50%-25% battery charge.
· SOLID RED: <25% battery charge.
>50%
>25%
>75%
<75%
<50%
D D
<15% battery charge: The system will automatically
switch to Level 1 power assist/Eco Mode to save battery.
You can adjust the level of power assist, if you prefer.
<10% battery charge: The system will turn off the pow-
er assist. The ebike lights will stay on for safety reasons
(if in use), and the system will keep recording its location
to allow the user to stop the activity.
TURNING THE SYSTEM ON/OFF
AND CHANGING THE ASSIST LEVEL
To turn the bicycle ON, press the Iwoc One once. The sys-
tem will turn ON and the Iwoc One will show the current
battery level in the corresponding color code.
>75%
To turn the bicycle OFF, press and hold the Iwoc One.
The Iwoc One will show a white light and the system will
turn OFF.
1 s
>25% >15% >10%
TECHN ICA L MAN UAL B LUE PAPER GAIN · HYDRO 2021
To adjust the power assist level, press the Iwoc One one
time. The current power assist level will then blink on screen
in the corresponding color code. While still blinking, press
the Iwoc One again to adjust the power assist level. The
corresponding color codes for the power assist levels are:
TURNING THE LIGHTS ON/OFF
If lights are connected to the X35 system using the
Ebikemotion® specific cable and compatible lights, they can
be turned on and off as follows:
Press the Iwoc One button once. While it's blinking, press
the Iwoc One button again and hold until the LED turns solid
ON yellow. The lights will turn on. Repeat the same procedure
to turn the lights off.
OFF
ASSIST OFF ASSIST 1 ASSIST 2
SYSTEM ERRORS
The Iwoc One and Iwoc Trio will indicate an error in the
system by displaying a pink light.
SOLID PINK: The system has gone into SAFE mode. Take
the ebike to an Orbea dealer to diagnose the problem.
BLINKING PINK: There is an error in the system. Check
the User App, which will display the error code, and refer
to the User App troubleshooting guide in this manual to
fix the error. If the error is not fixed or there is no solution
/
a user can apply, take the ebike to an Orbea dealer to
diagnose the problem.
1 s
The lights on Gain, both front and rear, are
programmed as running lights, so they will
turn on automatically when the bicycle is
switched on and will turn off when the bicycle
is switched off.
Once the bicycle has been turned on, the
lights can be switched off using the Iwoc One
following the method described above.
However, if the user prefers that the lights do
not turn on upon turning on the bicycle, this
behaviour can be modified by an Orbea dea-
ler using the Mahle Ebikemotion Dealer App.
O RB EA | 19
EN
ASSIST 3
· WHITE: No power assist
· GREEN: Level 1
· ORANGE: Level 2
· RED: Level 3
X
# ERROR