Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Frame Rail
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: F24703
Wrenches: 14mm, 17mm, 7/8"
Drill Bits: None
Frame Rail
Existing Weldnut
o
n
j
Qty. (1)
Carriage Bolt ½-13 x 1.75 GR5
k
Qty. (1)
Spacer Block ¼ x 1/1/2 x 3
l
Conical Toothed Washer ½"
Qty. (1)
1.
Remove two (2) existing bolts from frame.
2.
Install carriage bolt and block through tow hook as shown above.
3.
Raise hitch into position and install two (2) M10 bolts and conical toothed washers.
4.
Install conical toothed washer and nut on carriage bolt.
Tighten all M10 x 1.25 CL8.8 fasteners with torque wrench to 38 Lb.-Ft. (52 N*M)
Tighten all ½-13 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a
vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
z
2001, 2007, 2009, 2015 Cequent Performance Products
Installation Instructions
Hyundai Elantra
Fascia
(Sold separately)
Drawbar Kit:
3598
Drawbar must be used in the
RISE position only.
j
k
l
m
Trunk Pan
Tow Hook
Do Not Exceed Lower of Towing Vehicle
2000 LB (908 Kg.)Max Gross Trailer Weight
200 LB (90.8 Kg.)Max Tongue Weight
Wiring Access Location: PC3, PC4
m
Qty. (1)
Hex Nut ½-13
n
Qty. (2)
Hex Bolt M10 x 1.25 x 40mm CL8.8
o
Conical Toothed Washer 3/8"
Qty. (2)
Sheet 1 of 3
N24703
Part Numbers:
24703, 60868,
77089
Manufacturer's Rating or
Frame Rail
Existing Weldnut
o
n
10-20-15
Form F206 Rev A 5605
Rev. C
Publicidad
Manuales relacionados para Cequent Performance Products 24703
Resumen de contenidos para Cequent Performance Products 24703
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 N24703 10-20-15 Rev. C 2001, 2007, 2009, 2015 Cequent Performance Products Form F206 Rev A 5605...
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spé cifications en matiè re de sécurité des systèmes d’attelage. Feuille 2 de 3 N24703 10-20-15 Rev. C 2001, 2007, 2009, 2015 Cequent Performance Products Form F206 Rev A 5605...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulació n V-5 y SAE J684. Hoja 3 de 3 N24703 10-20-15 Rev. C 2001, 2007, 2009, 2015 Cequent Performance Products Form F206 Rev A 5605...