Publicidad
Idiomas disponibles
Idiomas disponibles
Hitch Shown In Proper Position
Equipment Required: Utility knife, tape measure & marking pencil,
plastic rivet gun, small punch, optional auto trim tools.
Fastener Kit: 75768F
Wrenches: 8mm.,10mm, 10mm deep socket, 18 mm
deep socket, flat screwdriver
1 1 1 1
Qty. (8)
Plastic rivet
Step 8
1.
Open tailgate to gain access to the rear taillights assembly.
2.
Using small screwdriver or a trim panel tool remove the plastic, covering the
fasteners.
3.
Remove the (2) nuts holding the taillight in place. Then carefully remove the taillights
assembly using flat bladed screwdriver to gently walk the taillight off the threaded
post. Unplug the taillight from the vehicle wiring. Both sides.
4.
Remove the rear reflector from the rear fascia, being careful not to scratch the fascia.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a
vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
© 2013 Cequent Performance Products, Inc
Installation Instructions
Fascia
Aluminum bumper
See next page for continuing instructions
Tighten all M12 fasteners with torque wrench to 65 Lb.-Ft. (88 N*M)
BMW X3
Do Not Exceed Lower of Towing Vehicle
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: SUV1&2
Galvanic isolator
Existing flanged nuts
Step 2
Step 3
Step 4
Step 2
Sheet 1 of 6
Part Numbers:
Manufacturer's Rating or
Max Gross
Trailer WT (LB)
4000 (1816 Kg)
3500 (1589 Kg)
Accessory Rating
Threaded studs
End panel
Step 8 Remove bolt
Step 4
75768N
1-31-13
Form: F205 Rev C 9-17-2012
75768
87632
44687
Max Tongue
WT (LB)
400 (182 Kg)
400 (182 Kg)
C
Rearward
Rev. A
Publicidad
Tabla de contenido
Manuales relacionados para Cequent Performance Products 75768
Resumen de contenidos para Cequent Performance Products 75768
- Página 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. © 2013 Cequent Performance Products, Inc Sheet 1 of 6 75768N 1-31-13 Rev.
-
Página 2: Installation Instructions
Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. © 2013 Cequent Performance Products, Inc Sheet 2 of 6 75768N 1-31-13 Rev. -
Página 3: Numéros De Pièce
Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. © 2013 Cequent Performance Products, Inc Feuille 3 de 6... - Página 4 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. © 2013 Cequent Performance Products, Inc Feuille 4 de 6...
-
Página 5: Números De Partes
No corte los orificios de acceso o accesorios con soplete. Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. © 2013 Cequent Performance Products, Inc Hoja 5 de 6... - Página 6 No corte los orificios de acceso o accesorios con soplete. Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. © 2013 Cequent Performance Products, Inc Hoja 6 de 6...