Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
FASCIA
Drawbar must be used in the
RISE position only.
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 24761F
Wrenches: 3/8" Drive Ratchet, 12mm socket, 10mm socket, 17mm socket
Drill Bits: N/A
j
Qty. (4)
Hex Bolt M10
k
Qty. (4)
Flat Washer
Remove 4 – bolts (2 per side) for muffler hangers.
1.
Remove 6 – bolts (4 per side) on heat shield and let hang down.
2.
3.
Slide rubber muffler hanger off of post on passenger side.
4.
Slide 2 rubber muffler hangers off of holders where the dual exhaust come together and let muffler assembly rest on cross
member in middle of vehicle.
5.
Slide hitch assembly into place with the hitch brackets to the inside of the frame rails.
6.
Bolt hitch to vehicle with fasteners supplied in fastener kit as shown.
7.
Insert the supplied (4) M10 hardware with flat and lock washers through bracket holes and thread into the weld nuts already in
the frame, hand tighten all supplied hardware.
8.
Tighten the (4) M10 CL8.8 fasteners with torque wrench to 42 Lb-ft.
9.
Re-install the 2 muffler hangers at the dual exhaust location.
10.
Re-install both heat shields
11.
Re-install rear muffler hangers
12.
Re-install passenger side muffler rubber mount.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2005, 2015 Cequent Performance Products, Inc. - Printed in Mexico
Installation Instructions
Hyundai Azera
(Sold separately)
Drawbar Kit:
3593
Weight Distributing
Wiring Access Location: N/A
l
m
Tighten all M10 fasteners with torque wrench to 42 Lb.-Ft.
Sheet 1 of 3
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Max Gross
Hitch type
Trailer WT (LB)
Weight Carrying
Ball Mount
EXISTING WELD NUTS
FRAME
j k l
Qty. (4)
Lock Washer
Qty. ()
24761N
Part Numbers:
24771
60837
77148
Max Tongue
WT (LB)
N/A
N/A
2000
200
10-13-15
Rev. C
Form: F205 Rev A 5-6-05
Publicidad
Manuales relacionados para Cequent Performance Products 24771
Resumen de contenidos para Cequent Performance Products 24771
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 24761N 10-13-15 Rev. C 2005, 2015 Cequent Performance Products, Inc. - Printed in Mexico Form: F205 Rev A 5-6-05...
- Página 2 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulació n V-5 y SAE J684 Hoja 2 de 3 24761N 10-13-15 Rev. C 2005, 2015 Cequent Performance Products, Inc. - Impreso en México Form: F205 Rev A 5-6-05...
- Página 3 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spé cifications en matière de sécurité des systèmes d’attelage. Feuille 3 de 3 24761N 10-13-15 Rev. C 2005, 2015 Cequent Performance Products, Inc. Imprimé au Mexique Form: F205 Rev A 5-6-05...