Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Hitch Shown In Proper Position
Equipment Required: Lubricant or Soapy water , Tape
Fastener Kit: 75648F
Wrenches: 3/4"
j
Qty. (2)
Carriage bolt 1/2-13 X 2.25 GR5
k
Qty. (2)
Spacer
l
Qty. (4)
Bevel spacer
m
Qty. (4)
Conical washer
1.
Lower muffler and tailpipe by removing all rubber isolators, behind rear axle. There will be (2) or (3) depending on vehicle.
Be careful not to allow mufflers to fall under their own weight. Note: Spraying a lubricant or soapy water on the metal hanger
rod and the rubber isolator helps removal.
2.
Feed spacers and carriage bolts into impact bar using the pull wires provided (both rail). Leave pull wire attached.
3.
Tape spacers in place to hitch before raising hitch into position. Orient spacer as shown. See Figure 2.
4.
Raise hitch into position, taking care not to push carriage bolts back into impact bar. Secure with conical washers and nuts.
Single exhaust -Raise hitch on the passenger side over exhaust pipe and slowly rotate hitch into position.
Dual exhaust - Slide hitch above tailpipes.
Bend and insert handle nuts thru access holes in frame and install two (2) 1/2"-13 bolts and conical washers as shown.
5.
6.
Tighten all fasteners to the required torque specification. Caution: Hold handle nuts in place to prevent them from rotating.
Bend end out of the way
7.
Raise exhaust back into position and reattach to rubber isolators. NOTE: If additional exhaust clearance is required, bend
exhaust hanger bracket, which is welded to vehicle frame, downward.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a
vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
z
2013 Cequent Towing Products – Printed in Mexico
Installation Instructions
Fascia
Impact bar
Frame
rail
p
m
n
m
o
Figure 1.
Single exhaust shown for clarity
Tighten 1/2-13 carriage bolts with torque wrench to 75 Lb.-Ft. (102 N*M)
Tighten 1/2-13 Handle nuts with torque wrench to 50 Lb.-Ft. (68 N*M)
Dodge Journey
Do Not Exceed Lower of Towing Vehicle
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: SUV 1, 2
k
q
l
j
l
Note: Fasteners
typical both sides
n
Qty. (2)
Hex nut 1/2-13
o
Qty. (2)
Hex bolt 1/2-13 X 1.50 GR5
p
Qty. (2)
Handle nut
q
Qty. (2)
Pull wire
Sheet 1 of 3
Part Numbers:
Manufacturer's Rating or
Max Gross
Trailer WT (LB)
4000 (1816 Kg)
4000 (1816 Kg)
l
m
Figure 2.
Orient spacers as shown.
HINT: Tape spacers in
place to hitch before
raising hitch into position
75648N
3-1-13
75648
87487
44601
Max Tongue
WT (LB)
400 (182 Kg)
400 (182 Kg)
j
Impact
k
bar
Hitch
bracket
l
n
Rearward
Rev. B
Publicidad
Manuales relacionados para Cequent Towing Products 75648
Resumen de contenidos para Cequent Towing Products 75648
- Página 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. 2013 Cequent Towing Products – Printed in Mexico Sheet 1 of 3 75648N 3-1-13 Rev.
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. 2013 Cequent Towing Products – Imprimé au Mexique Feuille 2 de 3...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York. V.E.S.C. Regulación V-5 y SAE J684 2013 Cequent Towing Products – Impreso en México Hoja 3 de 3...