Descargar Imprimir esta página
Ocultar thumbs Ver también para PRO Serie:

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

WARNING: With a 5000 lb. rated receiver the cargo carrier can carry a maximum 500 lb. load, with a 3500 lb. rated receiver it
can carry a maximum 300 lb. load. DO NOT EXCEED lower of vehicle mfg's or hitch mfg's maximum tongue
weight rating.
WARNING: Not for transport of people, animals, or flammable liquids.
WARNING: If the load or cargo carrier blocks or impairs visibility of the taillights or turn signals, the optional light kit must be used.
WARNING: If the cargo carrier or the contents being transported is in line with the exhaust outlet, an exhaust tip must be used to
redirect the exhaust flow away from the cargo platform or contents.
WARNING: Do not lubricate threads. Bolt failure may occur due to over tightening.
WARNING: Securely fasten load to cargo carrier. Attach straps and/or tie down hooks to the tubular frame of cargo carrier.
WARNING: Do not attach tie down straps or hooks to the mesh cargo floor. Do not over-tighten ratcheting straps, damage to
cargo carrier may result from over-tightening.
WARNING: Do not carry any loads wider than your vehicle.
WARNING: Do not drill (except where specified for license plate mounting) or weld to this product.
WARNING: Relocate license plate if blocked by load or cargo carrier.
TOOLS REQUIRED
19MM WRENCH
TORQUE WRENCH
FIG. 2
SHANK MUST BE USED IN THE RISE POSITION ONLY
ASSEMBLE TRAY
a. Place tray on a flat surface with the cargo mesh floor facing up as shown.
b. Place the support tube in between the two support rails on the bottom of the tray. Attach the tube to the bottom of the tray using
the
M12 X 55mm long
c. Tighten all bolts. Torque M12 CL9.8 bolts to 75 ft•lb. Torque M8 CL9.8 bolts to 25 ft•lb.
LOADING
Load the Cargo Carrier so that most of the weight is in the center of the platform.
5,000 lb. weight carrying hitch, and 300 lb. with a 3,500 lb. weight carrying hitch hitch.
FIG. 3
IMPORTANT NOTE: If the Cargo Carrier or cargo blocks the license plate, you can mount the license plate directly to the back of
the Cargo Carrier. Use the license plate as a template to mark two holes to drill. Diameter of the holes will depend on the screws
(not included) you are using, but should not exceed 1/4" diameter (6.35mm).
© 2005, 2006, 2009 Cequent Performance Products, Inc
63152N Rev C 9-16-09
INSTALLATION INSTRUCTIONS
FIG. 1
(63154) or
M12 X 80mm long
CORRECT
CARGO CARRIER
M12 X 80mm LG. CL9.8 (63152)
M12 X 55mm LG. CL9.8 (63154)
LOCKNUT
(3) PLACES
(63152) hex bolts as shown in Figure 1.
Cequent Performance Products, Inc
47774 Anchor Ct W.
Plymouth, MI 48170
Product No
63152
63154
Support Tube
Maximum load rating is 500 lb. with a
INCORRECT
Printed in XXXXX
.

Publicidad

loading

Resumen de contenidos para Cequent Performance Products PRO Serie

  • Página 1 Cargo Carrier. Use the license plate as a template to mark two holes to drill. Diameter of the holes will depend on the screws (not included) you are using, but should not exceed 1/4” diameter (6.35mm). Cequent Performance Products, Inc Printed in XXXXX © 2005, 2006, 2009 Cequent Performance Products, Inc 47774 Anchor Ct W. 63152N Rev C 9-16-09 Plymouth, MI 48170...
  • Página 2 (non comprises) utilisées, pourvu qu’elles n’excèdent pas ¼ po de diamètre (6,35 mm). Cequent Performance Products, Inc Printed in XXXXX © 2005, 2006, 2009 Cequent Performance Products, Inc 47774 Anchor Ct W. 63152N Rev C 9-16-09...
  • Página 3 Use la placa como guía para marcar dos orificios para perforar. El diámetro de los orificios dependerá de los tornillos (no incluidos) que use, pero no debe superar 1/4“ de diámetro (6.35mm). Cequent Performance Products, Inc Printed in XXXXX © 2005, 2006, 2009 Cequent Performance Products, Inc 47774 Anchor Ct W. 63152N Rev C 9-16-09 Plymouth, MI 48170...

Este manual también es adecuado para:

6315263154