Descargar Imprimir esta página
Ocultar thumbs Ver también para PRO Serie:

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Please read all instructions carefully before assembly, installation and/or use of this product.
WARNING: The Maximum capacity is 400 pounds. DO NOT EXCEED lowest of: vehicle mfg's, hitch weight carry
tongue weight, or cargo basket rating. Use with class 3 or higher 2" receiver hitch.
WARNING: Keep all body parts away from ramp sections when opening and closing ramp.
WARNING: Not for transport of people, animals, or flammable liquids.
WARNING: Do not ride equipment up ramp.
WARNING: Do not lubricate threads. Bolt failure may occur due to over tightening.
WARNING: Do not drill or weld to this product.
SPRING CLIP DETAIL
4
1
Qty. (1)
Latch Arm
2
Qty. (5)
Hex Bolt, 3/8-16 x 1.00 Gr5
3
Qty. (5)
Hex Locknut, 3/8-16
4
Qty. (1)
Spring Clip
5
Qty. (2)
Screw, Self-Tapping #8
NOTE: This ramp is designed for use with cargo basket 1040100.
ASSEMBLY INSTRUCTIONS:
1.
Attach the two halves of ramp with the 3/8 hex bolts and locknuts as shown above.
2.
Tighten 3/8 bolts until snug and ramp sections swing freely.
WARNING: DO NOT PLACE ANY BODY PARTS BETWEEN RAMP SECTIONS WHEN OPENING OR CLOSING RAMP.
3.
Install the lock pin, coil spring, flat washer, and lock nut into hole on side of ramp as shown.
4.
Tighten the 1/4-20 locknut until there is approximately 5/8" between the flat washer and ramp tube – see lock pin detail.
5.
Attach the spring clip in orientation shown using two #8 self-tapping screws – see spring clip detail.
Cequent Performance Products
47774 Anchor Court West
Plymouth, MI 48170
Technical Service: (888) 521-0510
7 8 9
5
Item:
Description:
2 3
6
6
Qty. (1)
Lock Pin
7
Qty. (1)
Coil Spring
8
Qty. (1)
Flat Washer, 1/4
9
Qty. (1)
Hex Locknut, 1/4-20
Page 1 of 3
1040200
CARGO RAMP
TOOLS REQUIRED:
7/16 Wrench
9/16 Wrench
Phillips Screw driver #2
5/8"
LOCK PIN DETAIL
1040200N
REV D
10-14-09

Publicidad

loading

Resumen de contenidos para Cequent Performance Products PRO Serie

  • Página 1 Tighten the 1/4-20 locknut until there is approximately 5/8” between the flat washer and ramp tube – see lock pin detail. Attach the spring clip in orientation shown using two #8 self-tapping screws – see spring clip detail. Cequent Performance Products 47774 Anchor Court West...
  • Página 2 Attach the latch arm to the cargo basket by installing the 3/8 hex bolt through the 3/8 diameter hole on basket as shown. Tighten 3/8 lock nut until snug and latch arm swings freely. Cequent Performance Products Printed in China...
  • Página 3 • Securely fasten load to cargo carrier. • Check security of load, fasteners, pin, and clip at fuel and rest stops. SPRING CLIP FIGURE 3 Cequent Performance Products Printed in China 47774 Anchor Court West Plymouth, MI 48170 Page 3 of 3...
  • Página 4: Instructions D'assemblage

    Serrer le contre-écrou 1/4-20 jusqu'à obtenir environ 5/8 po entre la rondelle frein et le tube de rampe – voir le détail de la goupille de verrouillage. À l'aide de deux vis autotaraudeuses #8, fixer la bride-ressort selon l'orientation indiquée – voir le détail de la bride-ressort. Cequent Performance Products 47774 Anchor Court West Plymouth, MI 48170...
  • Página 5 Fixer le bras de verrouillage sur le panier porte-bagages en posant un boulon hexagonal 3/8 dans le trou de 3/8 po de diamètre du panier, comme illustré. Serrer le contre-écrou 3/8 fermement mais sans excès, le bras de verrou doit bouger librement. Cequent Performance Products Imprimé en Chine 47774 Anchor Court West...
  • Página 6 • Par mesure de sécurité, vérifier la charge, les attaches, les chevilles et agrafes lors des haltes à la station-service ou l'aire de repos. ATTACHE À RESSORT FIGURE 3 Cequent Performance Products Imprimé en Chine 47774 Anchor Court West Plymouth, MI 48170...
  • Página 7: Rampa De Carga

    Apriete la tuerca de bloqueo de 1/4-20 hasta que haya aproximadamente 5/8” entre la arandela plana y el tubo de la rampa – ver el detalle del pasador de bloqueo. Instale el gancho de resorte en la orientación que se indica usando dos tornillos autorroscantes #8 – ver el detalle del gancho de resorte. Cequent Performance Products 47774 Anchor Court West Plymouth, MI 48170 Página 1 de 3...
  • Página 8 Instale el brazo pasador en la canasta de carga al instalar el perno hexagonal de 3/8 a través del orificio de 3/8 de diámetro en la canasta como se muestra. Apriete la tuerca de bloqueo de 3/8 hasta que esté firme y el brazo pasador gire libremente. Cequent Performance Products Impreso en China 47774 Anchor Court West Plymouth, MI 48170 Página 2 de 3...
  • Página 9 • Revise la seguridad de la carga, sujetadores, pasador y gancho en las paradas por combustible y de descanso. GANCHO DE RESORTE FIGURA 3 Cequent Performance Products Impreso en China 47774 Anchor Court West Plymouth, MI 48170 Página 3 de 3...

Este manual también es adecuado para:

1040200