Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Receiver Shown In Proper Position
Equipment Required:
Fastener Kit: K65015
Wrenches: 13/16", 15/16", 21mm
Drill Bits: None
Frame Rail
Leaf
Spring
1
Qty. (2)
Hex Bolt, 9/16"-12 x 1-3/4"
2
Qty. (2)
Spacer, 1-1/2" x 2" x 1/4"
3
Qty. (2)
Flat Washer, 9/16"
1.
Remove the four (4) M12 hex nuts from bumper mounting bolts.
CAUTION: THE BUMPER IS NOW LOOSE FROM THE VEHICLE. PROVIDE SUPPORT.
NOTE: The bumper may be removed for easier access into frame for hex bolt & block.
2.
Raise hitch into position aligning holes in hitch with holes in frame and brackets as shown.
3.
Feed hex bolts and spacers through ends of frame rails with pull wire and loosely install through frame and hitch.
4.
Reinstall bumper (if applicable) and loosely install hex nuts.
5.
Realign bumper and tighten all fasteners to specified torque.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2005 Cequent Towing Products
Front Mounted Receiver
Installation Instructions
Ford F-250 HD 4WD, F-350 4WD
Bumper
Existing M12 Hex Nut
4 Places
Frame Bracket
Access Hole
For 13/16" Wrench
(Underside Of Frame)
Tighten all 9/16 GR5 fasteners with torque wrench to 110 Lb.-Ft (149 N-m).
Tighten all M12 fasteners with torque wrench to 68 Lb.-Ft (92 N-m).
CARGO CAPACITY – DO NOT EXCEED
500 LB. OR VEHICLE FRONT GROSS
AXLE WEIGHT RATING. (GAWR)
9000
Existing Bumper
Mounting Bolts
4
Qty. (2)
Hex Nut, 9/16"
5
Qty. (2)
Pull Wire, 1/2"
Sheet 1 of 3
N65015
Part Numbers:
65015
LB. MAX. WINCH LINE PULL
Bumper
11-07-05
Bumper
Bracket
Rev. A
Publicidad
Manuales relacionados para Cequent Towing Products 65015
Resumen de contenidos para Cequent Towing Products 65015
- Página 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 N65015 11-07-05 Rev. A 2005 Cequent Towing Products...
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 N65015 11-07-05 Rev. A 2005 Cequent Towing Products...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York. V.E.S.C. Regulación V-5 y SAE J684. Hoja 3 de 3 N65015 11-07-05 Rev. A 2005 Cequent Towing Products...