Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Frame
Rail
Bumper
Stabilizer Bar
Stabilizer Bar
Bracket
Receiver Shown In Proper Position
Equipment Required:
Fastener Kit: K65016
Wrenches: 10mm, 15mm, 17mm , 3/4"
Drill Bits: 1/2"
j
Qty. (4)
Hex Bolt, M10 x 1.5 x 35
k
Lock Washer, 7/16"
Qty. (4)
l
Hex Bolt, 1/2"-13 x 1.75
Qty. (2)
NOTE: If front mounted license plate is present, repositioning is necessary.
1.
Remove stabilizer bar fasteners and brackets allowing stabilizer bar to swing free.
2.
Remove lower fascia and license plate mounting bracket (if existing).
3.
Raise receiver, stabilizer bar and stabilizer bar brackets into position and install all fasteners (except drivers side forward fastener) as shown
above.
NOTE: Receiver side brackets go between frame rails and stabilizer bar brackets.
4.
Using hitch as a template drill 1/2" hole in drivers side frame rail thru forward attachment hole and install fasteners.
5.
If desired, trim and reinstall the lower fascia. CONSULT VEHICLE OWNER BEFORE TRIMMING.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2005, 2012 Cequent Towing Products
Front Mounted Receiver
Installation Instructions
GMC Savanna
Chevrolet Express
Existing Weldnuts
Typical Both Sides
Stabilizer Bar
Stabilizer Bar
Bracket
Tighten all 1/2" GR5 fasteners with torque wrench to 75 Lb.-Ft (102 N-m).
Tighten all M10 CL8.8 fasteners with torque wrench to 38 Lb.-Ft (52 N-m).
CARGO CAPACITY – DO NOT EXCEED
500 LB. OR VEHICLE FRONT GROSS
AXLE WEIGHT RATING. (GAWR)
9000
Drilled Hole
Recovery
Eye
m
Lock Washer, 1/2"
Qty. (2)
n
Handle Nut, 1/2"
Qty. (2)
Sheet 1 of 3
N65016
Part Numbers:
65016
LB. MAX. WINCH LINE PULL
1-9-12
Rev. B
Publicidad
Manuales relacionados para Cequent Towing Products 65016
Resumen de contenidos para Cequent Towing Products 65016
- Página 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. 2005, 2012 Cequent Towing Products Sheet 1 of 3 N65016 1-9-12 Rev.
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. 2005, 2012 Cequent Towing Products Feuille 2 de 3 N65016 1-9-12 Rev.
- Página 3 Observe las precauciones de seguridad al trabajar por debajo del vehículo y use protección visual. No corte el acceso o los orificios del accesorio con soplete. Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York. V.E.S.C. Regulación V-5 y SAE J684. 2005, 2012 Cequent Towing Products Hoja 3 de 3 N65016 1-9-12 Rev.