Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Sliding Door Child Lock
HS012 User Guide
WARNING:
• ADULT ASSEMBLY REQUIRED. KEEP SMALL PARTS AWAY FROM CHILDREN DURING ASSEMBLY.
• In the event of an emergency, push forcefully on door to override the child lock. Overriding lock may damage it.
CAUTION:
• This product is not a toy. Do not allow children to play with it. When not in use, keep out of reach of children.
• This product is only a deterrent. It is not a substitute for proper adult supervision. Discontinue use when child becomes old enough to
defeat it.
BEFORE YOU BEGIN:
• Read all instructions before installing.
• Keep these instructions for future use.
• Remove all contents from packaging and discard box, and/or poly bags.
• Do not return this product to the place of purchase. If any parts are missing, email consumer@djgusa.com, call Consumer Relations at (800) 544-1108,
or fax at (800) 207-8182. You can also visit our website at www.safety1st.com. Have the model number ready (HS012) and date code (manufacture
date) located on located on product.
• Tools needed: Hand drill or power drill, 3/32" drill bit, Phillips head screwdriver, scissors & pencil (not provided).
• Avoid letting children see how you operate child safety devices. Watching you disengage a lock or latch could enable them to learn sooner how to
defeat it.
Parts & Features
A
Spacers (2 "A", 1 "B" and 1 "C")
B
Lock plate
C
Lock
D
1" Screws (4)
E
SecureTech
F
SecureTech™ locking button
G
Spacer installation template
H
Catch installation template (cut
out from Figure 1 below)
Prepare to Install
1
Cut out the catch installation template located on this page to the
right (Figure 1).
©2010 Dorel Juvenile Group. All Rights Reserved. Todos derechos reservados.
www.djgusa.com (800) 544-1108 www.safety1st.com Made in CHINA. Hecho en CHINA.
Styles and colors may vary. Los estilos y los colores pueden variar.
Distributed by (distribuido por) Dorel Juvenile Group, Inc., 2525 State St., Columbus, IN 47201-7494
Dorel Distribution Canada, 873 Hodge, St. Laurent, QC H4N 2B1 07/08/10 4358-5322
locking indicator
TM
B C
A
D
1
1
Green = Locked
Red = Unlocked
E
G H
F
Cut out this template
Publicidad
Manuales relacionados para Safety 1st HS012
Resumen de contenidos para Safety 1st HS012
- Página 1 • Do not return this product to the place of purchase. If any parts are missing, email consumer@djgusa.com, call Consumer Relations at (800) 544-1108, or fax at (800) 207-8182. You can also visit our website at www.safety1st.com. Have the model number ready (HS012) and date code (manufacture date) located on located on product.
- Página 2 Prepare to Install (continued) Open the sliding door approximately 5” (12.7 cm) and locate the gap above the sliding door (Figure 2). Determine which spacer(s) you need by inserting the spacer installation template into the gap (Figure 3). Make sure to hold template flat against top edge of track.
- Página 3 Relaciones con el Consumidor al (800) 544-1108, o envíe un fax al (800) 207-8182. También puede visitar nuestro sitio web en www.safety1st.com. Tenga a mano el número de modelo (HS012) y el código de fecha (fecha de fabricación), indicados en el producto.
- Página 4 Preparación (continuación) Abra la puerta corrediza aproximadamente 5 pulg. (12.7 cm) y localice la separación por encima de la puerta corrediza (Figura 2). Determine qué espaciador(es) necesita insertando la plantilla de instalación de espaciador(es) en la separación (Figura 3). Asegúrese de mantener la plantilla plana contra el borde superior del carril.