Numark NVII Guia Del Usuario página 13

Effects Controls
49. FX 1, FX 2, FX 3: These buttons have different functions on each Deck depending on the
current FX Mode: Single-FX Mode or Multi-FX Mode.
•
Single-FX Mode: FX 1 activates or deactivates the effect; FX 2 activates or
deactivates the first effect parameter (if applicable); FX 3 activates or deactivates the
second effect parameter (if applicable). Press and hold Shift and press FX 1 to
select the desired effect. Alternatively, press and hold Shift and then turn the FX
Knob under the effect name to move quickly through the list.
•
Multi-FX Mode: The buttons activate or deactivate the first, second, and third
effects in the effects chain, respectively. Press and hold Shift and press one of the
buttons to select the effect for that point in the effects chain. Alternatively, press and
hold Shift and then turn the FX Knob under the effect name to move quickly
through the list.
50. FX 1 Knob, FX 2 Knob, FX 3 Knob: These knobs have different functions on each Deck
depending on the current FX Mode: Single-FX Mode or Multi-FX Mode
•
Single-FX Mode: the FX 1 Knob controls the "wet-dry" balance of the effect; the FX
2 Knob controls the first effect parameter; the FX 3 Knob controls the second effect
parameter. When Touch Mode is activated, touch the FX 1 Knob to activate its
effect, and release the knob to deactivate it.
•
Multi-FX Mode: The knobs control the "wet-dry" balance of the first, second, and
third effects in the effects chain, respectively. When Touch Mode is activated, touch
a knob to activate its effect, and release the knob to deactivate it.
51. Beat / Mode: Tap this button repeatedly at the desired tempo to set the rate of the
effects' low-frequency oscillators (LFOs). Press and hold this button to reset Beat
Multiplier to the Deck's BPM. Press and hold Shift and then press this button to switch
between Single-FX Mode and Multi-FX Mode.
52. Beat Knob: Turn this knob to set the Time Division for the selected effects.
53. FX Assign: Use these buttons to apply Effect A and/or B to the corresponding channel.
You can apply Effect A and/or B to the entire Program Mix by using the FX Send buttons
below the Master Volume knob. (Each effect can be applied to any or all of the four
channels and/or the Program Mix.)
54. Channel Filter: Turn this knob to adjust the filter on the corresponding channel. The type
of filter it adjusts will depend on the Filter Mode button.
55. Filter Mode: Press this button to toggle through the Filter Modes, which affect the
Channel Filter knobs: Off, Filter-Roll Mode, or Filter-FX Mode.
•
Off: When this button is off, the Channel Filter knob will apply and adjust a low-
pass filter to the corresponding channel when turned counter-clockwise or a high-
pass filter when turned clockwise.
•
Filter-Roll Mode: Press this button once to activate Filter-Roll Mode (the button will
light solid red). The Channel Filter knob will apply and adjust a low-pass filter to the
corresponding channel when turned counter-clockwise or a high-pass filter when
turned clockwise. In addition, it will apply a Loop Roll to the filter and will decrease
in length as the knob moves further away from the center position. Press this button
once to deactivate Filter-Roll Mode.
•
Filter-FX Mode: Press and hold Shift and then press this button to activate Filter-FX
Mode (the button will flash red). The Channel Filter knob will apply and adjust a
low-pass filter to the corresponding channel when turned counter-clockwise or a
high-pass filter when turned clockwise. In addition, it will adjust Parameter 1 of the
effects applied to that channel as the knob moves further away from the center
position. Press this button once to deactivate Filter-FX Mode.
13