Wieland SA-BM-S1-4EKL Manual Del Usuario página 8

Connecting terminals and LED displays
Terminal Function
A1 Operating voltage connection U
A2 Operating voltage connection earth
X1, X2 Outputs for supplying device inputs or controlling sensors
EN Input for enabling all outputs ENABLE
S1 Control circuit input (cf. Tables 2 and 3)
S2 Control circuit input (cf. Tables 2 and 3)
S3 Control circuit input (cf. Tables 2 and 3)
I1 – I4 Inputs for connecting sensors
Q1 / Q2 Outputs group A (semiconductor)
Q3 / Q4 Outputs group B (semiconductor)
Setting the Function Blocks
Use the FUNCTION rotary switch to select the function block for the respective safety application. Function blocks where inputs I1 - I4 are assigned
to a function group AB are designated single functions. Function blocks where inputs I1, I2 are assigned to function group A and inputs I3, I4 are
assigned to function group b are designated combination or dual functions. In the combination functions the function group B (grey background) is
hierarchically subordinate to function group A. In other words, if function group A is shut down, function group B will be shut down too (regardless of
the status of inputs I3, I4). Dual function 8 possesses two separate function groups A and B. Regardless of the selected function block, you can use
the DELAY rotary switch to set a release delay for outputs Q3 and Q4 (cf. Table 1). The start function of the function groups and the possibility of
retriggering the release delay are defined by the configuration of control inputs S1 - S3. When operating voltage is connected, the status of these
control inputs is read (cf. Tables 2 and 3).
FUNCTION rotary switch (Table 1)
Function
Safety application
group
0 Switch position not allowed
Emergency stop, safety door, switching mat (with QE)
1
OR
Safety door monitoring 1 NC, 1 NO (with QE)
2
OR
3.1 non-contact safety device type 4 (without QE)
3 3.2 PDF (X1-I1) / non-contact safety device type (X2-I2)
Muting
4 Two-hand function EN 574 III C (with QE)
Emergency stop, safety door (with QE)
5
5.1 Two-hand function EN 574 III A (with QE)
5.2 Inching with 5 s confirmation limit (with QE)
Emergency stop, safety door (with QE)
6
Emergency stop, safety door (with QE)
Emergency stop, safety door, non-contact safety device
type 4 (without QE)
7
Emergency stop, safety door, non-contact safety device
type 4 (without QE)
Emergency stop, safety door, non-contact safety device
type 4 (without QE)
8
Emergency stop, safety door, non-contact safety device
type 4 (without QE)
Emergency stop, safety door (with QE)
9
Emergency stop, safety door, non-contact safety device
type 4 (without QE)
U - signal from X1 or X2 or U
x
*Flashing if Reset-Required
8
B
or semiconductor outputs from sensors / QE - cross monitoring
B
LED Meaning if LED on
PWR Operating voltage U
EN High level on terminal
S1 High level on terminal
S2 High level on terminal
S3 High level on terminal
I1 – I4 High level on terminal
Q1 / Q2 U on terminal
B
Q3 / Q4 U on terminal (even if flashing)
B
FLT Error (see also "Error Codes of Error LED")
Input assigment
Q1
X1 I1
X2 I2 NO
DELAY DELAY
U I3
B
U I4
B
X1 I1
X2 I2 NO
DELAY DELAY
U I3
B
U I4
B
U I1
x
U I2
x
NO
X1 I1
DELAY DELAY
X2 I2
U I3
B
U I4
B
X1 I1
X1 I2 NO
X2 I3 DELAY DELAY
X2 I4
X1 I1
X2 I2 NO
DELAY DELAY
X1 I3
X2 I4
X1 I1
X2 I2 NO
DELAY DELAY
X1 I3
X2 I4
U I1
x
U I2 NO
x
DELAY DELAY
U I3
x
U I4
x
U I1
x
U I2 NO
x
DELAY DELAY
U I3
x
U I4
x
X1 I1
X2 I2 NO
DELAY DELAY
U I3
B
U I4
B
present
B
Output function
Q2 Q3 Q4
NO
DELAY DELAY
NO
DELAY DELAY
Muting
NO lamp/
DELAY
Reset-
Required*
NO NO NO
DELAY DELAY
NO NO NO
DELAY DELAY
NO NO
DELAY
DELAY
NO NO
DELAY
DELAY
NO NO
DELAY
DELAY
NO NO
DELAY
DELAY