Safety Instructions; Product Description - Master B21T Manual De Instrucciones

3

SAFETY INSTRUCTIONS

PRODUCT DESCRIPTION

GB
UNPACKING
SAFETY INSTRUCTIONS
!!! IMPORTANT: Please read the instructions carefully
and thoroughly before assembling, using or cleaning
the appliance. The use of the heater can cause severe
injury due to burns, fire or electrical discharge.
This appliance is transportable and made especially for
closed quarters such as warehouses, shops and homes, as
well as for humid and damp quarters such as construction
sites. The appliance complies with directive EN 60335-2-
30/1998, Keymark all.B control, and therefore directive B.T.
73/23/EEC and 93/68EEC
•
Keep the appliance at a minimum-security distance of
0.5 metres from combustible materials. Never use the
appliance in rooms where petrol, solvents, paints or any
other substance that gives off combustible gases, are
kept, or near curtains or other drapery.
•
Keep the appliance out of the reach of children and
animals.
•
Only use the appliance with a power supply that
complies with the frequency and voltage requirements
specified on the rating plate.
•
Use only three wire extension power cables with ground
wire and adequate lengths.
•
Unplug the appliance from the outlet when not in use.
•
The appliance should never be positioned directly under
outlets.
•
Should the appliance be left temporarily in insecure
conditions, make sure that it cannot be used and that
the plug is disconnected.
•
Do not use this heating device near washbasins,
bathtubs, showers or swimming pools.
•
Before beginning any kind of maintenance or repairs on
the appliance make sure the plug is definitely
disconnected from the outlet.
•
Do not cover the appliance; it could cause overheating.
PRODUCT DESCRIPTION
See fig. 1-2-3 Page. 1
1) Handle
2) Thermostat
3) Protective grid front
4) Resistance
5) Shell
6) Switch
UNPACKING
•
Remove all the material used to pack the appliance for
transportation.
•
Remove all the objects from the box.
PROBLEM
The appliance works but does not heat.
The appliance does not switch on
Limited air flow
FUNCTIONING
PERIODIC STORAGE AND CONTROL
SINGLING OUT PROBLEMS
7) Cable press
8) Protective grid back
9) Electric cable
10) Base
11) Fan
12) Motor
13) Plug
SINGLING OUT PROBLEMS
CAUSE
Resistance is burnt out
Thermostat control is broken
Security device was set off
Faulty motor
Power supply interrupted
Air duct obstructed
Faulty motor
•
If the heater looks damaged, immediately inform the
retailer where the appliance was bought.
FUNCTIONING
!!! WARNING: Read the instructions in the safety
information section thoroughly. The instructions must
be followed carefully in order for the heater to function
safely.
Make sure the electric cable is not damaged in any way. If
the electric cable is damaged it must be immediately
replaced by the manufacturer, by the Service Center or by
specialized personnel only. Make sure that the electrical
characteristics of the outlet correspond to the requirements
stated in the instruction booklet and/or on the rating plate
found on the appliance.
Place the appliance in an upright position.
TURNING ON THE HEATER
Plug the electric cable into the outlet.
Rotate the knob to the required position:
fig.4-Page1 Fan only
fig.5-Page1 Minimum capacity
fig.6-Page1 Maximum capacity
SWITCHING OFF THE HEATER
Let the fan run for 3 minutes before turning the heater off.
Rotate the knob to the "0" position.
REGULATING THE THERMOSTAT
By rotating the knob that controls the thermostat (fig.7-
Page1), you can regulate the room temperature.
When the desired temperature is reached the thermostat
automatically switches the resistance off but the fan
continues working.
MANUAL RESETTING
The appliance comes with a built in security device that
goes off automatically if the appliance should happen to
overheat.
If the security device should go off, let the appliance cool
down before looking for the cause of the problem.
Push the "RESET" button (Fig.7-Page1) with a small push
rod to reset the appliance.
Should the problem persist, contact the Service Centre.
PERIODIC STORAGE AND CONTROL
If the appliance is not used for a long period of time, it
should be cleaned before being put away. Store it in a dry
place and protect it from dust. When the appliance is used
again check to make sure that the electric cable is not
damaged. Should you have any doubts as to the conditions
of the appliance please contact the Service Center.
The appliance should be checked at least once a year.
Only qualified personnel authorized by the manufacturer
must carry out all repairs.
SOLUTION
Replace
Replace
Push "RESET"(Fig.7-Page1)
Replace
Unplug the appliance and check connection.
Clear the passage
Replace