Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Hitch Shown In Proper Position
Equipment Required: Pull wires (Provided)
Fastener Kit: 24824F
Wrenches: 13mm, ¾"
Drill Bits: None
This slot is to clear
Stud in frame rail
3 3 3 3
4 4 4 4
Figure 1
1 1 1 1
Qty. (4)
Carriage Bolt ½-13 x 1.75 GR5
2 2 2 2
Qty. (4)
Spacer Block ¼ x 1 x 3
3 3 3 3
Qty. (4)
Conical Toothed Washer ½"
1.
Lower exhaust as follows:
On Driver's side: Disconnect rubber exhaust hanger forward of muffler.
On Passenger's Side: Remove exhaust hanger bracket by removing (2) M8 fasteners. Discard M8 fasteners.
2.
Fishwire carriage bolts and ¼ x 1 x 3 spacer blocks up thru large slots in each frame rail and down thru attaching holes as shown above. See
Figure 3.
Note: On passenger's side, refer to Figure 2 to reverse fishwire block and bolt up thru large slot and back down thru same slot.
3.
Raise hitch into position, being careful not to push bolts back into frame, and secure with conical toothed washers and nuts.
Note: Trim or bend heat shield as necessary to allow hitch installation.
4.
Tighten all ½" GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
5.
Raise exhaust back into position. On driver's side, re-attach rubber exhaust hanger. On passenger's side, re-attach exhaust hanger bracket
with M8 x 1.25 x 35mm Hex bolt ass'ys provided with hitch, thru slots in side bracket into weldnuts in vehicle frame.
6.
Tighten all M8 x 1.25 CL9.8 fasteners to 20 Lb.-Ft. (27 N*M
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a
vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
z 2009, 2015 Cequent Performance Products – Printed in Mexico
Installation Instructions
Volkswagen Eos
(Sold separately)
Drawbar Kit:
3594
Drawbar must be used in the
RISE position only.
Frame Rail
2 2 2 2
1 1 1 1
Exhaust hanger bracket
On passenger's side
4 4 4 4
5 5 5 5
)
Sheet 1 of 3
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (90.8) Max Tongue Weight
Wiring Access Location: xxx
A. Insert bolt and
B. Align block on
Block into frame
Reverse Fishwiring procedure
3 3 3 3
4 4 4 4
5 5 5 5
Qty. (4)
Hex Nut ½-13
Qty. (2)
Hex Bolt Ass'y M8 x 1.25 x 35mm CL9.8
24824N
Part Numbers:
24824
77196
60211
C. Pull bolt thru
access hole
block
Figure 2
2 2 2 2
1 1 1 1
Figure 3
Kink pull wire to keep
Spacer independent of bolt
10-8-15
Rev. C
Form F206 Rev A 5605
Publicidad
Manuales relacionados para Cequent Performance Products 24824
Resumen de contenidos para Cequent Performance Products 24824
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. z 2009, 2015 Cequent Performance Products – Printed in Mexico Sheet 1 of 3...
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 24824N 10-8-15 Rev. C z 2009, 2015 Cequent Performance Products - Imprimé au Mexique Form F206 Rev A 5605...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. Hoja 3 de 3 24824N 10-8-15 Rev. C z 2009, 2015 Cequent Performance Products - Impreso en México Form F206 Rev A 5605...