Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 75527F
Wrenches: 17mm, 19mm, 22mm, 3/4, 7/8
Drill Bits: None
Bumper Bracket
Fasteners Typical Both Sides
Qty. (4)
M12 X 1.25 CL9.8 X 40mm Hex Bolt
Qty. (6)
Conical Toothed Washer
Qty. (4)
M14 X 2.00 CL10.9 X 40mm
Qty. (4)
5/8 Flat Washer
Qty. (4)
5/8 Lock Washer
1.
Remove angle brackets from the inside surface between the frame rails and the bumper brackets.
2.
Raise hitch into position and install M12 bolts and conical toothed washers into existing weldnuts.
3.
Install M14 bolts through the vehicle bumper bracket, through the hitch and fasten with flat washer, lock washer, and hex nut.
4.
Install 1/2-13 hex bolts and 1/4 block through the bumper bracket, through the hitch and fasten with conical toothed washers
and hex nuts.
5.
Tighten all fasteners to the required torque specifications.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2011 Cequent Performance Products
Installation Instructions
Toyota Tundra
Bumper
Angle Bracket
Both Sides
Frame Rail
Tighten all 1/2-13 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Tighten all M12 X 1.25 CL9.8 fasteners with torque wrench to 105 Lb.-Ft. (142 N*M)
Tighten all M14 X 2.00 CL10.9 fasteners with torque wrench to 115 Lb.-Ft. (156 N*M)
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: PU3
Qty. (4)
M14 Hex Nut
Qty. (2)
1/2-13 X 1.75 Hex Bolt
Qty. (2)
1/4 X 1.00 X 2.00 Block
Qty. (2)
1/2 Hex Nut
Sheet 1 of 3
75527N
Part Numbers:
75527 44568
87434 78222
Max Gross
Max Tongue
Trailer WT (LB)
8000 (3632 Kg)
800 (363 Kg)
6000 (2724 Kg)
600 (272 Kg)
Existing Weldnuts
4/18/11
Form: F205 Rev A 5-6-05
WT (LB)
Rev. B
Publicidad
Manuales relacionados para Cequent Performance Products 75527
Resumen de contenidos para Cequent Performance Products 75527
- Página 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. 2011 Cequent Performance Products Sheet 1 of 3 75527N 4/18/11 Rev.
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. 2011 Cequent Performance Products Feuille 2 de 3...
- Página 3 Observe las precauciones de seguridad al trabajar por debajo del vehículo y use protección visual. No corte los orificios de acceso o accesorios con soplete. Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. 2011 Cequent Performance Products Hoja 3 de 3 75527N 4/18/11 Rev.