Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Frame Rail
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 24827F
Wrenches: 17mm, 11/16"
Drill Bits: 3/8"
.50 [12.70mm]
3/8" dia. Drilled holes
Access hole modification to allow
Pull wire of block and carriage bolt
Figure 2.
Passenger side only
1 1 1 1
Qty. (2)
Carriage bolt 7/16-14 X 1.75 GR5
2 2 2 2
Qty. (2)
Spacer
3 3 3 3
Qty. (4)
Conical washer 7/16"
If present, remove the tie down brackets from vehicle frame rail. Return bolts and tie down bracket to owner.
1.
Remove the (2) plastic rivets that fasten the fascia tabs to the vehicle. Note: Remove the center of the rivet with a screwdriver.
2.
Enlarge the access holes in the vehicle passenger frame rail only to accept the spacer. See Figure 2.
3.
Feed the pullwire through the newly enlarged hole, attach spacer and bolt and feed one at a time into the frame rail. Leave the
pullwire attached.
4.
Paint any exposed metal
5.
Raise hitch into position, feed pull wires thru adjacent holes in the hitch, remove pull wires and attach conical washers and nut
finger tight only (Be careful not to push fastener back into frame rail). Hand tighten.
6.
Check to assure hitch is centered on vehicle.
7.
Torque all fasteners to specifications.
8.
Reinstall plastic rivets back into bumper fascia.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2008, 2015 Cequent Towing Products – Printed in México
Installation Instructions
Fascia
(Sold separately)
Drawbar Kit:
3593
Drawbar must be used in
the Rise position only.
1.00 [25.40mm]
Kink Pull wire to keep
spacer independent of
bolt
Existing 3/4"
Diameter hole
in frame
Tighten all M10 CL 8.8 fasteners with torque wrench to 59 Lb.-Ft. (80 N*M)
Tighten all 7/16-14 GR5 fasteners with torque wrench to 50 Lb.-Ft. (68 N*M
Scion tC
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (90.8 Kg) Max Tongue Weight
Wiring Access Location:
6
Enlarge Hole
Passenger side only
Frame Rail
Existing weldnuts
3
Figure 1.
5
4 4 4 4
Qty. (2)
Hex nut 7/16-14
5 5 5 5
Qty. (2)
Hex bolt M10 X 1.25 X 30 CL8.8
6 6 6 6
Qty. (2)
Pull wire 7/16
Sheet 1 of 3
24827N
Part Numbers:
24827, 60213,
77199
1
2
3
4
10-8-15
Rev. B
Form F206 Rev A 5605
Publicidad
Manuales relacionados para Cequent Towing Products 24827
Resumen de contenidos para Cequent Towing Products 24827
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. 2008, 2015 Cequent Towing Products – Printed in México Sheet 1 of 3 24827N 10-8-15 Rev.
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 24827N 10-8-15 Rev. B 2008, 2015 Cequent Towing Products – Imprimé au Mexique Form: F205 Rev A 5-6-05...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York. V.E.S.C. Regulación V-5 y SAE J684 2008, 2015 Cequent Towing Products – Impreso en México Hoja 3 de 3...