Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Impact bar
Tow hook
Hitch Shown In Proper Position
Equipment Required: Sealant
Fastener Kit: 24810F
Wrenches: 3/4", Crowfoot adaptor
4 2
Seal existing drain holes
in trunk pan to prevent
intrusion of exhaust
fumes and
water.
1
Qty. (1)
Carriage bolt ½-13 x 2.25 GR5
2
Qty. (4)
Spacer
3
Qty. (3)
Conical washer
1.
Remove trunk panel to gain access to end panel. Remove spare tire cover.
2.
Remove (2) trunk rubber plugs located in the end panel. Return to owner.
3.
Place carriage bolt and spacers (2) onto tow hook. As shown Figure 1.
4.
Raise hitch into position behind end panel and fasten to tow hook with conical washer and hex nut. Hand tighten.
5.
Install fasteners on drivers side. Place spacer (Item 2) inside trunk add sealant around hole. Install fastener as
shown in Figure 1 or optional Figure 2. Hand tighten to prevent hitch from moving while installing passenger side.
6.
Install fastener on passenger side. Once again adding sealant around hole. Install fasteners as shown in Figure 1
or optional Figure 2 .
7.
Tighten all fasteners to specification listed below.
8.
Apply sealant at bolt attachments inside spare tire well to prevent the intrusion of water and exhaust fumes to
vehicle interior.
9.
Reinstall trunk panel. Reinstall spare tire cover
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2008 Cequent Towing Products
Installation Instructions
Chevrolet Aveo Sedan
Fascia
Drawbar Kit:
3593
Drawbar must be used in the
RISE position only.
Remove
rubber
plugs
1
2
2
3
4
3
4
Tighten all ½" Gr5 fasteners with torque wrench to 75 Lb.-Ft. ( 102 N*M)
End panel
Bar
Tow hook
Inside
trunk
Figure 1.
4
Qty. (3)
Hex nut ½-13
5
Qty. (2)
Carriage bolt ½-13 x 2.00 GR5
6
Qty. (1)
½" Pull wire
Sheet 1 of 3
Part Numbers:
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (91 Kg) Max Tongue Weight
Wiring Access Location: PC3, 4
2
43
Inside
trunk
End panel
2
Bar
5
34
Figure 2.
Optional fasteners assembly.
24810N
3-7-08
Form F206 Rev A 5605
24810
60896
77181
End panel
Bar
5
Optional trunk
fasteners assembly
Spacers (item 2)
must be inside of
trunk.
Rev. A
Publicidad
Manuales relacionados para Cequent Towing Products 24810
Resumen de contenidos para Cequent Towing Products 24810
- Página 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. 2008 Cequent Towing Products Sheet 1 of 3 24810N 3-7-08 Rev.
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. 2008 Cequent Towing Products Feuille 1 de 3...
- Página 3 Observe las precauciones de seguridad al trabajar por debajo del vehículo y use protección visual. No corte los orificios de acceso o accesorios con soplete. Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. 2008 Cequent Towing Products Sheet 1 of 3 24810N 3-7-08 Rev.