Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Hitch Shown In Proper Position
Equipment Required: Jig saw or Cut-off wheel
Fastener Kit: 24820F
Wrenches: 10mm, 7/8"
EVAP Canister
1
Qty. (4)
Bolt Carriage – ½-13 x 1-3/4"
2
Qty. (4)
Block – ¼ x 1 x 2
1.
For ease of installation, remove the EVAP retaining nut and move the EVAP canister off to the side to expose more of the inside
drivers side frame rail. Hoses can stay attached.
2.
With a jig saw or a cut-off wheel join the two holes shown in fig. 1 and fig. 2. This will allow an access hole for the bolt and blocks.
3.
Paint any bare metal to prevent rusting.
4.
Fish wire bolt and block (item 1 and 2) into the frame through the access hole made in step 2 and locate through mounting holes as
shown above.
5.
Raise hitch into position, make sure not to push the bolts back into the frame.
6.
Install the rest of the fasteners (item 3 and 4). Adjust hitch side-to-side if needed and tighten fasteners.
7.
Reinstall EVAP canister and nut.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2008 Cequent Towing Products
Installation Instructions
MITSUBISHI LANCER
Drawbar Kit:
3593
Drawbar must be used in the
RISE position only.
Tow
hook
1
2
3
4
EVAP
retaining nut
Tighten all ½" fasteners with torque wrench to 75 Lb.-Ft. (102 n*m)
Tighten all M6 fasteners with torque wrench to 3 Lb.-Ft. ( 4 n*m)
Do Not Exceed Lower of Towing Vehicle
2000 LB (908 kg) Max Gross Trailer Weight
200 LB (90.8 kg) Max Tongue Weight
Wiring Access Location: PC3, PC4
Muffler support
Fig. 1
3
Qty. (4)
Washer Conical – ½"
4
Qty. (4)
Hex nut – ½-13
Sheet 1 of 3
24820N
Part Numbers:
Manufacturer's Rating or
Existing holes
7/8"
Mounting
hole
Cut between holes
For bolt access
09-15-08
Form F206 Rev A 5605
24820
60207
77192
Mounting
hole
Fig. 2
Rev. A
Publicidad
Manuales relacionados para Cequent Towing Products 24820
Resumen de contenidos para Cequent Towing Products 24820
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 24820N 09-15-08 Rev. A 2008 Cequent Towing Products Form F206 Rev A 5605...
- Página 2 Ne jamais utiliser une torche pour découper un accès ou un trou de fixation. Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 24820N 09-15-08 Rev. A 2008 Cequent Towing Products Form F206 Rev A 5605...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. Sheet 3 of 3 24820N 09-15-08 Rev. A 2008 Cequent Towing Products Form F206 Rev A 5605...