Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
BUMPER
MOUNT
Hitch Shown In Proper Position
Equipment Required: Flat blade Screwdriver, Fishwire (provided).
Fastener Kit: 24816F
Wrenches: 11/16"
Drill Bits: 1/2"
BUMPER MOUNT
FISHWIRE
BUMPER
FIGURE 3.
1
2
3
4
1
Qty. (4)
7/16"-14 X 1-1/4" GRADE 5 CARRIAGE BOLT
2
Qty. (4)
BLOCK 1/4" X 1" X 3"
1. Use 1/2" drill bit to enlarge the four existing attachment holes.
2. With the flat blade screwdriver remove and retain (2) plastic push rivets that attach lower fascia supports to vehicle.
3. Fishwire carriage bolts and blocks through ends of the bumper as shown in Figure 1.
4. Position hitch as shown in Figure 2.
5. Fishwire carriage bolts and blocks through ends of the bumper mounts as shown in Figure 2.
6. Tighten all fasteners.
7. Replace plastic rivets removed in Step 2.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2006, 2007, 2008 Cequent Towing Products
Installation
BUMPER
FASCIA
Drawbar must be used in the
RISE position only.
1
2
3
4
Tighten all 7/16" fasteners with torque wrench to 50 Lb.-Ft. (68 N*M)
Instructions
Mazda 3
including Speed 3
Drawbar Kit:
3592
1
2
3
4
FIGURE 2.
3
Qty. (4)
4
Qty. (4)
Sheet 1 of 3
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
2000 LB (908 kg) Max Gross Trailer Weight
200 LB (91 kg) Max Tongue Weight
Wiring Access Location: PC3, PC4
FIGURE 1.
FISHWIRE
1
2
3
4
BUMPER MOUNT
BRACKET ENLARGED
USE THIS
SLOT FOR
4 - DOOR
MODELS
7/16" CONICAL TOOTHED WASHER
7/16"-14 HEX NUT
24816N
5-28-08
Part Numbers:
24816
77188
60201
24816U
BUMPER
USE THIS
SLOT FOR
5 - DOOR
MODELS
AND
SPEED 3
Rev A
Form F206 Rev A 5605
Publicidad
Manuales relacionados para Cequent Towing Products 24816
Resumen de contenidos para Cequent Towing Products 24816
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 24816N 5-28-08 Rev A 2006, 2007, 2008 Cequent Towing Products Form F206 Rev A 5605...
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 24816N 5-28-08 Rev A 2006, 2007, 2008 Cequent Towing Products Form F206 Rev A 5605...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684 Hoja 3 de 3 24816N 5-28-08 Rev A 2006, 2007, 2008 Cequent Towing Products Form F206 Rev A 5605...