Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 75696F
W
Wrenches: 10mm, 19mm,
h
10
19
Extension, Large screwdriver
Drill Bits: None
1
1
2
3
1
Qty. (6)
Flat Washer, 1/2"
2
Qty. (6)
Lock Washer, 1/2"
For vehicles with appearance panel: Remove appearance panel which covers the trunk pan. This panel will need to be trimmed or not reinstalled
on vehicle. Ask vehicle owner their choice before starting installation. See Figure 2
1.
Remove plastic plugs, from existing holes (if present).
2.
Raise hitch into position over the exhaust pipes aligning the slots in the hitch with the weldnuts in the bottom of the frame rails. NOTE:
Lowering exhaust may ease installation. Spraying a lubricant on the metal hanger rod and the rubber isolator helps removal.
3.
Install fasteners as shown above.
4.
Torque all fasteners to specifications shown below.
5.
Raise exhaust back into position, if lowered prior to hitch installation.
6.
Reinstall trimmed cover panel removed. Or return untrimmed panel to vehicle owner.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2010 Cequent Performance Products
Installation Instructions
Toyota Sienna
Fascia
6" Ratchet
6" Ratchet
Frame Rail
Existing Weldnut
3 Places
(Both Sides)
Note:
Fasteners Typical
Both Sides
Figure 1
Tighten all M12 CL10.9 fasteners with torque wrench to 75 Lb.-Ft (102 N-m).
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: SUV1, 2
Sport Model
Area to be trimmed
3
Qty. (6)
Hex Bolt, M12 x 1.25 x 40mm
Sheet 1 of 3
75696N
Part Numbers:
75696
87586
44648
78194
U-Haul
Max Gross
Max Tongue
Trailer WT (LB)
WT (LB)
5000 (2270 Kg)
500 (227 Kg)
3500 (1589 Kg)
350 (159 Kg)
To be reinstalled
Area to be trimmed
Area to be trimmed
Figure 2
To be reinstalled
8-12-10
Rev. B
Publicidad
Manuales relacionados para Cequent Performance Products 75696
Resumen de contenidos para Cequent Performance Products 75696
- Página 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 75696N 8-12-10 Rev. B 2010 Cequent Performance Products...
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 75696N 8-12-10 Rev. B 2010 Cequent Performance Products...
- Página 3 Este producto cumple con las especificaciones y requerimientos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. Página 3 de 3 75696N 8-12-10 Rev. B 2010 Cequent Performance Products...