Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Rearward
Hitch Shown In Proper Position
Equipment Required: Metal snips
Fastener Kit: 24923F
Wrenches: 17mm, 19mm
Drill Bits: None
Frame rail
Note: Fasteners typical both sides.
j
Qty. (6)
Bolt M12 X 1.25 X 40 CL10.9
1. Lower exhaust by removing four rubber isolators (two per side).
2. Remove six M12 bolts (three per side). Lay two exhaust brackets to the side. Return fasteners to owner.
3. Raise hitch into place over heat shield, or trim heat shield as shown in figure 2 on both sides of vehicle. Sandwich
hitch between vehicle frame and exhaust hanger brackets. Install provided fasteners as shown.
4. Torque all hardware to specification below.
5. Raise exhaust back into position and reattach to rubber isolator.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a
vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
z
2014, 2015 Cequent Performance Products, Inc-
Installation Instructions
Fascia
(Sold separately)
Drawbar Kit:
Drawbar must be used in the
RISE position only.
Existing weldnuts on
top side of vehicle
frame
Figure 1
Tighten all M12 CL10.9 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Printed in Mexico
Lexus IS 250
Lexus IS 350
3594
k
k
j
j
k
Conical washer 1/2"
Qty. (6)
Sheet 1 of 3
Part Numbers:
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (90.8 Kg) Max Tongue Weight
Wiring Access Location:
Figure 2
3"
Optional Heat Shield
Trimming
Exhaust hanger
bracket
24923N
10-05-15
Form F206 Rev B 9-17-2012
24923
60358
77310
PC 3, 4
Rev. B
Publicidad
Manuales relacionados para Cequent Performance Products 24923
Resumen de contenidos para Cequent Performance Products 24923
- Página 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. 2014, 2015 Cequent Performance Products, Inc- Sheet 1 of 3 24923N 10-05-15 Rev.
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spé cifications en matiè re de sécurité des systèmes d’attelage. – 2014, 2015 Cequent Performance Products, Inc Feuille 2 de 3...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulació n V-5 y SAE J684. – z 2014, 2015 Cequent Performance Products, Inc Hoja 3 de 3 24923N 10-05-15 Rev.