Cequent Towing Products 36284 Instrucciones De Instalación

Optional Drawbar (Sold Separately)
For Legacy Outback Only 36053
Drawbar must be used in the RISE
Position only.
Frame Rail
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: K36284
Wrenches: 12mm, 11/16, ¾, 7/8
Drill Bits: None
43221 43221 43221 43221
Hitch
*Passenger's side requires
two (2) ¼ x 1 x 2 spacers
Item
Tie-Down Bracket
Figure 2
1 1 1 1 Qty. (2) Hex Bolt ½-13 x 2-1/4 GR5
2 2 2 2
Qty. (5) Spacer ¼ x 1 x 2
3 3 3 3
Qty. (2) Lockwasher 1/2
4 4 4 4 Qty. (2) Hex Nut ½-13
1. Lower carbon canister and bracket from passenger side frame rail.
2. Remove the four (4) plastic caps from bottom of frame rails. Fishwire carriage bolts and blocks through access hole in bottom of
frame as shown in Figure 1.
Note: On driver's side, side bracket attaches to the outboard side of the tie-down bracket. On passenger's side, side bracket
attaches to the inboard side of the tie-down bracket.
3. Raise hitch into position. Loosely install hex nuts and conical toothed washers onto forward most fasteners. Install hex bolts and
blocks as shown in Figure 1.
Note: On passenger's side, place additional block between hitch and tie-down bracket. See Figure 2.
4. Reinstall large plastic caps into access holes removed in step 2. Reattach carbon canister and bracket.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a
vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
z 1999, 2001, 2003, 2004, 2007,2015 Cequent Towing Products – Printed in Mexico
Installation Instructions
Subaru Legacy Sedan
Subaru Legacy Wagon
Subaru Legacy Outback
Fascia
(Sold separately)
Drawbar must be used in the
Rise position only.
Side Bracket
2 2 2 2
Tighten all 7/16-14 GR5 fasteners with torque wrench to 50 Lb.-Ft. (68 N*M)
Tighten all ½-13 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Drawbar Kit:
36061
Wiring Access Location: PC1, PC2
Figure 1
5 5 5 5 Qty. (2)
6 6 6 6
Qty. (2)
7 7 7 7
Qty. (2)
8 8 8 8 Qty. (2)
Sheet 1 of 3
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
3500 LB (1589 Kg) Max Gross Trailer Weight
300 LB (136 Kg) Max Tongue Weight
Note: Fasteners Typical Both Sides
Access Hole
8765 8765
8765 8765
*
Carriage Bolt 7/16-14 x 1-1/2 GR5
Spacer ¼ x 1 x 3
Conical Toothed Washer 7/16
Hex Nut 7/16-14
N36284
Part Numbers:
36284
06287
90176
Frame Rail
10-22-15 Rev. E
Form F206 Rev A 5605