Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Frame rail
Fascia
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 24912F
Wrenches: 11/16
Drill Bits: None
Access
hole
Kink pull wire to keep
spacer independent of bolt
Reverse pull wire procedure
j
Qty. (4)
Carriage bolt 7/16-14 X 1.50 GR5
k
Spacer 1/4" X 7/8" X 3"
Qty. (4)
l
Conical tooth washer 7/16"
Qty. (4)
Note: if additional clearance is needed for installation. Lower exhaust system at the rubber isolators. Spraying a lubricant on the metal hanger rod
and the rubber isolator helps removal.
Raise the hitch into position, feed the pull wires though the adjacent slots on the hitch.
1.
2.Feed the pull wire into the rearward slot and out the access hole. Attach spacer and carriage bolt to pull wire and feed into frame rail, pull into
position. Both sides. See Figure 2. Leave pull wire attached.
3.Using the reverse pull wire procedure Figure 3. Feed the pull wire into position both rails. Leave pull wires attached.
4.Carefully remove pull wires. One at a time place the washer over the pull wire and use it to hold the bolt in place while carefully removing the pull
wire, then attach the hex nut.
5.Tighten all fasteners to the required torque specification.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a
vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
z
2013, 2015 Cequent Performance Products
Printed in Mexico
Installation Instructions
Mazda 3 sedan
(Sold separately)
Drawbar Kit :
3593
Drawbar must be used in the
RISE position only.
j
k
n
l
m
n
Tighten all 7/16-14 Gr5 fasteners with torque wrench to 50 Lb.-Ft. (68 N*M)
Frame rail
Note: Fasteners typical
both sides
Forward
m
Qty. (4)
Hex nut 7/16-14
n
Pull wire 7/16"
Qty. (4)
Sheet 1 of 3
24912N
Part Numbers:
24912
60344
77299
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (90.8 Kg) Max Tongue Weight
Wiring Access Location: PC3, 4
Forward
Rearward
slot
Access
hole
10-05-15
Form F206 Rev B 9-17-2012
slot
Rev. B
Publicidad
Manuales relacionados para Cequent Performance Products 24912
Resumen de contenidos para Cequent Performance Products 24912
- Página 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. 2013, 2015 Cequent Performance Products Sheet 1 of 3 24912N 10-05-15 Rev.
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spé cifications en matiè re de sécurité des systèmes d’attelage. 2013, 2015 Cequent Performance Products Feuille 2 de 3...
- Página 3 Observe las precauciones de seguridad al trabajar por debajo del vehí culo y use protecció n visual. No corte los orificios de acceso o accesorios con soplete. Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulació n V-5 y SAE J684. 2013, 2015 Cequent Performance Products Hoja 3 de 3 24912N 10-05-15 Rev.