Troubleshooting - Toro PowerPlex Manual Del Usuario

Troubleshooting

Perform only the steps described in these instructions. All further inspection, maintenance, and repair work
must be performed by an authorized service center or a similarly qualified specialist if you cannot solve the
problem yourself.
Problem
The flashlight does not turn on (battery
pack Model 88541 only).
The USB port does not work (battery pack
Model 88541 only).
The battery pack loses charge quickly.
The battery charger is not working.
The tool does not run or run continuously.
The battery pack shows only 3 LED
indicators after only a few seconds of
using a fully charged battery.
All 4 LED indicators are blinking on
the battery pack after you press the
battery-charge-indicator button on the
battery pack and the current charge
displays (when the battery pack is not in
use).
All 4 LED indicators are blinking on the
battery pack after releasing the trigger
(when the battery pack is in use).
2 LED indicators are blinking on
the battery pack after you press the
battery-charge-indicator button on the
battery pack and the current charge
displays (when the battery pack is not in
use).
2 LED indicators are blinking on the
battery pack after releasing the trigger
(when the battery pack is in use).
Possible Cause
1. The battery pack is on the charger.
2. The battery pack is over or under the
appropriate temperature range.
3. The battery pack voltage is low.
1. The battery pack is on the charger.
2. The battery pack is over or under the
appropriate temperature range.
3. The battery pack voltage is low.
4. The USB port is not compatible with all
small electronic devices.
1. The battery pack is over or under the
appropriate temperature range.
1. The battery charger is over or under
the appropriate temperature range.
2. The outlet that the battery charger is
plugged into does not have power.
1. There is moisture on the leads of the
battery pack.
2. The battery is not fully installed into the
tool.
1. This is a normal occurrence.
1. The battery pack is over or under the
appropriate temperature range.
1. The battery pack is over or under the
appropriate temperature range.
1. There is a difference in voltage
between cells in the battery pack.
1. There is a difference in voltage
between cells in the battery pack.
10
Corrective Action
1. Remove the battery pack from the
charger.
2. Move the battery pack to a place
where it is dry and the temperature is
between 0°C (32°F) and 40°C (104°F).
3. Place the battery pack on the charger.
1. Remove the battery pack from the
charger.
2. Move the battery pack to a place
where it is dry and the temperature is
between 0°C (32°F) and 40°C (104°F).
3. Place the battery pack on the charger.
4. Use the USB port to charge a different
small electronic device.
1. Move the battery pack to a place
where it is dry and the temperature is
between 0°C (32°F) and 40°C (104°F).
1. Unplug the battery charger and move
it to a place where it is dry and the
temperature is between 0°C (32°F)
and 40°C (104°F).
2. Contact your licensed electrician to
repair the outlet.
1. Allow the battery pack to dry or wipe it
dry.
2. Remove and then replace the battery
into the tool making sure that it is fully
installed and latched.
1. Stop the tool and press the
battery-charge-indicator button or
the remove the battery from the tool to
display the actual battery charge.
1. Move the battery pack to a place
where it is dry and the temperature is
between 0°C (32°F) and 40°C (104°F).
1. Move the battery pack to a place
where it is dry and the temperature is
between 0°C (32°F) and 40°C (104°F).
1. Place the battery on the charger until
it is fully charged.
1. Place the battery on the charger until
it is fully charged.