Descargar Imprimir esta página

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Hitch Shown In Proper Position
Equipment Required: Lubricant or
Soapy water
Fastener Kit: 24867F
Wrenches: 17mm, 18mm, 19mm
and 6" extension
Spray some lubricant on the rubber exhaust
hangers and then use a screwdriver or pry
bar to remove all of the rubber hangers.
Support the system while you remove all of
the hangers
j
Qty. (2)
Hex bolt M12 X 1.25 X 35mm CL8.8
k
1/2" Conical washer
Qty. (2)
1.
Remove and return factory tow hook and fasteners to vehicle owner. (4 Bolts)
2.
Lower exhaust system at the rubber isolator (3 places) leaving the rubber isolator attached to muffler. Note:
Spraying a lubricant or soapy water on the metal hanger rod and the rubber isolator helps removal. Be careful
not to allow muffler to fall under its own weight.
3.
Scrape undercoating and caulking from bottom of frame rails large enough to allow the hitch brackets to sit flush
against the frame rails. Clean out undercoating from weldnut (do not damage threads). Confirm M10 hex bolt
will thread into weldnuts.
4.
Raise hitch into position on driver's side and loosely install fastener as shown, installing a hex bolt and conical
washer thru elongated hole in hitch into vehicle frame. Raise hitch into position on passenger's side and loosely
install fastener as shown, installing hex bolt and conical washer thru elongated hole in hitch into vehicle frame.
Center hitch on vehicle and install remaining hardware as shown.
5.
Tighten all fasteners to the required torque specification.
6.
Reinstall exhaust.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2010, 2011, 2015 Cequent Performance Products – Printed in Mexico
Installation Instructions
Nissan Juke AWD
Fascia
(Sold separately)
Drawbar Kit:
Drawbar must be used in the
Rise position only.
Frame rails
Tighten all M10 CL 8.8 fasteners with torque wrench to 39 Lb.-Ft. (52 N*M)
Tighten all M12 CL 8.8 fasteners with torque wrench to 68 Lb.-Ft. (92 N*M
Do Not Exceed Lower of Towing Vehicle
3593
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (90.8 Kg) Max Tongue Weight
Wiring Access Location: SUV 3, 4
Rubber
isolator
m
l
l
Qty. (2)
Hex bolt M10 X 1.25 X 30mm CL8.8
m
3/8" Conical washer
Qty. (2)
Sheet 1 of 3
Part Numbers:
Manufacturer's Rating or
Weldnuts
- both sides
k
j
)
24867N
10-07-15
Form F206 Rev A 5605
24867
60284
77248
Rev. D

Publicidad

loading

Resumen de contenidos para Cequent Performance Products 24867

  • Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. 2010, 2011, 2015 Cequent Performance Products – Printed in Mexico Sheet 1 of 3...
  • Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 24867N 10-07-15 Rev. D 2010, 2011, 2015 Cequent Performance Products - Imprimé au Mexique Form F206 Rev A 5605...
  • Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulació n V-5 y SAE J684. Hoja 3 de 3 24867N 10-07-15 Rev. D 2010, 2011, 2015 Cequent Performance Products - Impreso en México Form F206 Rev A 5605...

Este manual también es adecuado para:

6028477248