Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Trunk pan
Vehicle frame
cross member
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 24857F
Wrenches: 8mm, 10mm, 18mm,
,
& 3/4
Vehicle end
panel
Rotate hitch behind fascia
Fig 2.
2.50 / 64mm
Xxxx
Driver's side
Appearance panel trim
Fig 3.
1
1
Qty (12)
Qty. (12)
Flat washers7/16"
Flat washers7/16
2
Qty. (1)
Carriage bolt ½-13 X 2.50 GR5
3
Qty. (3)
Spacers
1.
Remove both appearance panels, (10) 8mm, (4) 10mm retain for reinstallation.
2.
Remove (4) existing M12 flange nuts located on vehicle end panel as shown Fig 1. Spraying with a lubricant will assist the
removal. Retain for re-installion. Wash lubricant off studs, if used.
3.
Place (3) flat washers on each stud .
4.
Raise hitch into position by rotating hitch behind fascia as shown in Fig 2., reinstall existing flange nuts removed in step 2, finger
ti ht
tight only.
l
5.
Determine numbers of spacer needed between hitch bar and vehicle frame cross member (minimum of 1).
6.
Using pullwire insert carriage bolt and (1) spacer into vehicle frame cross member, thread pull wire through spacer/s and hitch bar
as shown Fig 4. Remove pull wire and install conical washer and hex nut onto carriage bolt.
7.
Tighten fasteners to torque specified.
8.
Reinstall appearance panel on passenger side.
9.
Drivers side appearance panel will need to be trimmed (see Fig 3) or returned to owner. Obtain owners permission
before trimming.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2010, 2011 Cequent Performance Products
Installation Instructions
Fascia
Drawbar must be used in the
Rise position only.
,
,
Existing
Existing
flange
Studs
nuts
Orient
spacers as
shown
Fig 4.
Pullwire example
Tighten all 12mm fasteners with torque wrench to 62 Lb.-Ft. (84 N*M)
Tighten all 12mm fasteners with torque wrench to 62 Lb. Ft. (84 N M)
Tighten all ½-13 GR 5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
BMW 328 Sedan
Drawbar Kit:
Do Not Exceed Lower of Towing Vehicle
3593
Wiring Access Location: P3, 4
1
Vehicle frame
cross member
cross member
Hitch
bar.
Fig 1.
Spacer to be
removed if
needed
4
4
Qty. (1)
Qty (1)
Conical washer 1/2
Conical washer 1/2"
5
Qty. (1)
Hex nut
6
Qty. (1)
Pullwire 1/2"
Sheet 1 of 3
Manufacturer's Rating or
M
f t
' R ti
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (90.8 Kg) Max Tongue Weight
4
5
24857N
6-3-11
Part Numbers:
24857
60273
77227
24863
U-Haul
2
3
Vehicle end panel
Rev. B
Form F206 Rev A 5605
Publicidad
Manuales relacionados para Cequent Performance Products 24857
Resumen de contenidos para Cequent Performance Products 24857
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 24857N 6-3-11 Rev. B 2010, 2011 Cequent Performance Products Form F206 Rev A 5605...
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 24857N 6-3-11 Rev. B 2010, 2011 Cequent Performance Products Form F206 Rev A 5605...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. Hoja 3 de 3 24857N 6-3-11 Rev. B 2010, 2011 Cequent Performance Products Form F206 Rev A 5605...