Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Bumper
Structure
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 36362F
Wrenches: 3/4"
j
Hex Bolt, 1/2-13 x 4"
Qty. (4)
k
Conical Washer, 1/2"
Qty. (4)
For vehicles with OEM Tow Hook: Tow hook
installation. Installation time will increase from 20 Min. to 90 Min.
1.
Lower the spare tire.
2.
Remove two plastic pins that hold bumper fascia onto bumper structure as shown in Figure 1. (If OEM tow hook is present:
Remove fascia, plastic bumper support and tow hook)
3.
Gently pull fascia rearward about one inch and raise the hitch into position as shown in Figure 1.
4.
If there is excessive gap between the vertical surfaces of the hitch and the bumper structures, flat washers should be used as
shims. They can be held in place using cellophane tape. See Figure 2.
5.
Secure hitch with fasteners. Fascia may contact the back of the hitch. (Reinstall fascia and plastic bumper support if removed
in Step 2.)
6.
Replace plastic pins in bumper fascia.
7.
Raise the spare tire into storage position.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2005, 2006, 2015 Cequent Performance Products – Printed in Mexico
Installation Instructions
Jeep Grand Cherokee
Jeep Commander
Bumper
Fascia
Drawbar Kit:
(Sold separately)
Drawbar must be used in the
DROP position only.
Fascia
Bumper
Structure
FIGURE 1
Tighten all 1/2-13 GR5 fasteners with torque wrench to 75 Lb.-Ft. (120 N*M)
Do Not Exceed Lower of Towing Vehicle Manufacturer's
36051
3500 LB (1589 Kg) Max Gross Trailer Weight
300 LB (136 N*M) Max Tongue Weight
Wiring Access Location: SUV1, SUV2
Pins
l
Flat Washer, 1/2"
Qty. (8)
must be permanently removed
Sheet 1 of 3
36362N
Part Numbers:
36362
06378
90114
Rating or
FIGURE 2
for hitch
10-19-15
Rev. E
Publicidad
Manuales relacionados para Cequent Performance Products 36362
Resumen de contenidos para Cequent Performance Products 36362
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. 2005, 2006, 2015 Cequent Performance Products – Printed in Mexico Sheet 1 of 3...
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spé cifications en matiè re de sé curité des systèmes d’attelage. Feuille 2 de 3 36362N 10-19-15 Rev. E 2005, 2006, 2015 Cequent Performance Products - Imprimé au Mexique...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York. V.E.S.C. Regulació n V-5 y SAE J684. Hoja 3 de 3 36362N 10-19-15 Rev. E 2005, 2006, 2015 Cequent Performance Products - Impreso en México...