Cequent Performance Products 36317 Instrucciones De Instalación

Hitch Shown In Proper Position
Equipment Required: Chisel, Hammer, Cut-off Wheel, Pull Wire (provided)
Fastener Kit: F36317
Wrenches: 13mm, 11/16, 3/4
Drill Bits: 3/8"
"
1-1/4
Figure 5
SS Model only
Frame Rail
Block
Figure 4
j
Qty. (4) Carriage Bolt 3/8-16 x 1.50
k
Qty. (4) Block 3/16 x 1-1/8 x 2
l
Conical Washer 3/8"
Qty. (4)
m
Qty. (4) Hex Nut 3/8-16
1. Lower muffler by removing the two (2) rearmost exhaust hangers.
2. Remove the bottom four (4) 8mm bumper bolts from the end panel.
Note: Do not loosen or remove the top bumper bolt.
3. Remove existing weldnut from end panel on the inboard side of frame rail (see figure 2).
If necessary, enlarge existing holes in end panel using a 3/8" drill.
4.
5. Raise hitch into position, aligning slots in hitch with holes in vehicle end panel.
Note: The upright bracket goes on the forward side of the end panel.
Note: SS Model requires fascia trim obtain vehicle owner's approval. See Figure 5.
Loosely install the 3/8" carriage bolts and blocks, conical washers and hex nuts as shown in figure 1.
6.
Fishwire 1/2" carriage bolt and block thru large slot in bottom of frame rail as shown. Orient blocks as shown (See Figure 4). Attach conical
7.
washers and nuts as shown.
Note: Keep bolt and block separate while inserting fasteners thru slot (see figure 3).
8. Tighten fasteners to specified torque ratings as follows:
Tighten all 3/8-16 GR5 fasteners with torque wrench to 30 lb.-ft. (41 N*M)
Tighten all ½-13 GR5 fasteners with torque wrench to 75 lb.-ft. (102 N*M)
9. Reinstall exhaust hangers removed in step 1.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a
vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
z
2003, 2006, 2015 Cequent Performance Products – Printed in Mexico
Installation Instructions
Chevrolet Malibu – Sedan Only*
Fascia
* -SS Model requires fascia trim
Obtain vehicle owner's approval
Drawbar Kit:
36071
Drawbar must be used in the
Rise position only.
Fascia
SS Model Only
Trim Here
1-
3/4"
Figure 1
(Sold separately)
Wiring Access Location: PC3, PC4
Remove M8 bolts. Enlarge existing
Holes with 3/8" drill if necessary
End Panel
Bumper
Top bumper bolt
(do not remove)
Remove existing plastic
Handle bolt and nut.
Enlarge existing holes with
3/8" Drill if necessary
n
Qty. (2) Carriage Bolt ½-13 x 2.00
o
Qty. (2) Block ¼ x 1-1/2 x 3
p
Conical Washer ½"
Qty. (2)
q
Qty. (2) Hex Nut ½-13
Sheet 1 of 3
Part Numbers:
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
3500 LB (1 589 Kg) Max Gross Trailer Weight
300 LB ( 136 Kg) Max Tongue Weight
Kink pull wire to keep block
independent of bolt
Fishwire
Figure 3
Remove existing weldnut
Figure 2
(Looking rearward on vehicle)
(Passenger side)
N36317 10-19-15
Form F206 Rev A 5605
36317
06988
90132
Vehicle frame
end panel
Rev. C