Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Frame rail
Hitch Shown In Proper Position
Equipment Required: Lubricant or Soapy water
Fastener Kit: 24903F
Wrenches: 17mm,
Bulkhead
Note: Fasteners typical
both sides
1 1 1 1
Qty. (4)
Hex bolt M10 X 1.25 X 30mm CL8.8
1.
Lower exhaust system at the rear rubber isolator leaving the rubber isolator in place on the vehicle. Spraying a lubricant on the metal hanger
rod and the rubber isolator helps removal
2.
Lift hitch into position, passengers side first. Place crosstube over top of tail pipe. Rotate into position on the outside of the frame rail. It may
be necessary to pull the fascia gently out of the way.
3.
Raise the drivers side of the hitch up so it's on the outside of the frame rails and in front of bulkhead (rotate as needed). Once again, it may be
necessary to pull the fascia gently out of the way.
4.
Attached remaining fasteners as shown.
5.
Push hitch toward the rear of the vehicle.
6.
Tighten all fasteners to the required torque specification.
7.
Reattach rubber muffler hanger.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
© 2013, 2015 Cequent Performance Products
Printed in Mexico
Installation Instructions
Kia Forte
Fascia
(Sold separately)
Drawbar Kit:
Drawbar must be used in the
Rise position only.
1 2
Rearward
Tighten all M10 CL 8.8 fasteners with torque wrench to 42 Lb.-Ft. (57 N*M)
Do Not Exceed Lower of Towing Vehicle
3594
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (90.8 Kg) Max Tongue Weight
Wiring Access Location: PC3,PC4
Existing weld nuts
Both sides.
Tail pipe
2 2 2 2
Qty. (4)
Sheet 1 of 3
24903N
Part Numbers:
24903
60335
77290
Manufacturer's Rating or
Frame rail
Conical washer 3/8"
10-6-15
Form F206 Rev B 5605
Rev. C
Publicidad
Manuales relacionados para Cequent Performance Products 24903
Resumen de contenidos para Cequent Performance Products 24903
- Página 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. © 2013, 2015 Cequent Performance Products Sheet 1 of 3 24903N 10-6-15 Rev.
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. © 2013, 2015 Cequent Performance Products Feuille 2 de 3...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. © Hoja 3 de 3 24903N 10-6-15 Rev. C 2013, 2015 Cequent Performance Products Impreso en México Form F206 Rev A 5605...