SKF TBK329WP Guia Del Usuario

SATURN
Model:
Vue 3.5L V6 2004-07
L66
Engine Identification:
11
10
(8-9 ft. lbs.)
AD18599
7
CA1
T
6
AD18599
13
8
AD18599
AD18599
DISCLAIMER OF WARRANTIES: Although this information has been obtained from sources generally thought to be reliable, no warranty (expressed or implied) can be made as to its accuracy or completeness, nor is any responsibility assumed by Autodata Publications Inc. or anyone connected with it for loss or
damages suffered through reliance on any information contained within it. In no event will Autodata Publications Inc. be liable for any damages, direct or indirect, consequential or compensatory, including, without limitation, lost profits, for any representations, breaches or defaults arising out of the use of this information.
Year:
1
AD18599
AD18599
13 7
CA2
WP
9
G
(33 ft. lbs.) AD18599
CS
AD18599
12
AD18599
4
1
(181 ft. lbs.)
5
2
AD18599
ENG
TBK329WP
Replacement Interval Guide
Saturn recommends replacement every
100,000 miles.
The previous use and service history of the vehicle
must always be taken into account.
Check For Engine Damage
CAUTION: This engine has been identified as an
INTERFERENCE engine in which the possibility of
valve-to-piston damage in the event of a timing belt
failure is MOST LIKELY to occur.
A compression check of all cylinders should be
performed before removing the cylinder head.
Labor Times – hrs
Remove & install
Special Tools
Crankshaft pulley holder – No.EN 46337.
º
Tensioner locking pin – No.EN 46330.
º
Tensioner pulley holder – No.EN 46331.
º
Special Precautions
Disconnect battery ground cable.
º
Do NOT turn crankshaft or camshaft with timing
º
belt removed.
Remove spark plugs to ease turning engine.
º
Turn crankshaft in normal direction of rotation
º
(unless otherwise stated).
Do NOT turn crankshaft via camshaft or other
º
sprockets.
Observe all tightening torques.
º
1. Raise and support front of vehicle.
2. Remove:
Right hand front lower splash guard.
¡
Air cleaner assembly.
¡
¡ Accessory drive belt.
3. Hold the crankshaft pulley with tool No.EN 46337.
4. Remove:
Crankshaft pulley bolt j
¡
Crankshaft pulley j
¡
Timing belt upper covers j
¡
Timing belt lower cover j
¡
Timing belt guide plate j
¡
5. Turn the crankshaft clockwise until No.1 cylinder at
3
TDC.
6. Ensure the crankshaft sprocket timing marks j
aligned.
7. Ensure the camshaft sprocket timing marks j
aligned.
8. Screw in tool No.EN 46331 j
NOTE: Tighten tensioner pulley holder finger
tight only. Do not overtighten.
9. Loosen the guide pulley bolt j
10. Remove the timing belt.
IMPORTANT: For maximum timing belt system
life, replace all tensioners and pulleys during
timing belt replacement.
1. Undo and remove bolts j
tensioner j
2. Align the hole in the tensioner body with the hole in
the pushrod and using a press with a maximum
force of 2200 lbs. slowly press the pushrod into the
auto tensioner body j
3. Retain pushrod in position j
4. Install auto tensioner j
j
3.10 to 8.0-9.0 ft. lbs.
1 0
5. Ensure the timing marks j
6. Install timing belt to the sprockets and pulleys in a
counterclockwise order starting at the crankshaft
sprocket.
7. Ensure timing belt taut between sprockets on
non-tensioned side.
8. Torque guide pulley bolt j
9. Remove the pin j
tensioner to operate.
10. Remove the tensioner pulley holder j
11. Install timing belt guide plate j
12. Install crankshaft pulley j
13. Install crankshaft pulley bolt j
14. Turn the crankshaft six turns clockwise until
No.1 cylinder at TDC.
15. Remove:
Crankshaft pulley bolt j
¡
Crankshaft pulley j
Removal
¡
Timing belt guide plate j
¡
16. Ensure the crankshaft sprocket timing marks j
aligned.
17. Ensure the camshaft sprocket timing marks j
aligned.
18. Install:
Timing belt guide plate j
¡
Timing belt lower cover j
¡
. Crankshaft pulley j
1
¡
.
Crankshaft pulley bolt j
2
¡
.
3 19. Torque the crankshaft pulley bolt j
.
4
20. Install components in reverse order of removal.
.
5
NOTE: After timing belt replacement the engine
control module (ECM) may require resetting.
Connect a suitable scan tool to the data link
are
6
connector and follow manufacturer's
instructions or return vehicle to dealer.
are
7
.
8
5 or 6 turns.
9
Installation
and remove auto
1 0
.
1 1
.
1 2
using tool No.EN 46330.
1 3
to engine and torque bolts
1 1
& j
are aligned.
6 7
to 33 ft. lbs.
9
from auto tensioner to allow
1 3
.
8
.
5
.
2
.
1
.
1
.
2
.
5
are
6
are
7
.
5
.
4
.
2
.
1
to 181 ft. lbs.
1
x
457TBIS329WP 4/5 Rev. 02/11
4 57 TBIS329P