Timex W-90 Manual De Instrucciones

THANK YOU FOR PURCHASING YOUR TIMEX WATCH.
EXTENDED WARRANTY
Available in U.S. only. Extend your warranty for an additional 4 years from date of purchase
for $5. You can pay with AMEX, Discover, Visa or MasterCard by calling 1 800-448-4639 during
normal business hours. Payment must be made within 30 days of purchase. Name, address,
telephone number, purchase date, and 5-digit model number required. You can also
mail a check for $5 to: Timex Extended Warranty, P.O. Box 1676, Dept. EF, Little Rock,
AR 72203.
Please read instructions carefully to understand how to operate your Timex watch.
Your model may not have all of the features described in this booklet.
Real-time calendar clock, Second time zone, Countdown timer, Daily/weekday/weekend alarm,
hourly chime, Chronograph with lap/split storage, INDIGLO® night-light with Night-Mode®
Feature.
SET OR DONE
(To save changes
and exit setting
MODE OR NEXT
(Proceed to
next step)
When setting, each button has a different function as indicated above. Watch face will indicate
when button changes function.
Note: On your watch the day/date display may appear below the time display and the Indiglo
button may be located at the 3 o'clock position.
Press MODE until DEMO appears. This mode will allow you to view all the features of the
watch. Each mode will appear for three seconds. Setting date will erase this feature. It will
reappear when you change the battery.
1. In TIME mode, press and hold SET. Time zone will flash.
2. To set, push + or – to select first or second time zone.
3. Press NEXT. Hour digits flash.
4. Press + or – to change hour including AM/PM. (Scroll through 12 hours to get to AM/PM).
5. Press NEXT. Minute digits flash.
6. Press + or – to change minutes.
7. Press NEXT. Second digits flash.
8. Press + or – to set seconds to zero.
9. Press NEXT. Day of week flashes.
10. Press + to – to change day.
11. Continue pattern to set month, day of month, 12-hour or 24-hour time display, MM.DD or
DD.MM date format, turn hourly CHIME on/off, turn BEEP on/off. If you select BEEP on, a
beep will sound every time you push a button (except INDIGLO).
12. Press DONE to confirm and exit or NEXT to continue and set second time zone, if desired.
13. When in Time mode, press and hold START/SPLIT to "peek" at second time zone; hold for 4
seconds to switch time zones.
Setting the ALARM is similar to setting TIME. Your watch model has three alarms. Follow below
procedure to set each alarm.
1. Press MODE repeatedly until ALM1, ALM2, or ALM3 appears. Select alarm you want to set.
2. Press SET to set alarm.
3. Hour digits flash. Press + or – to change hour.
4. Press NEXT. Minute digits flash. Press + or – to change minutes.
5. Press NEXT. If in 12-hour format, AM/PM flashes. Press + or – to change.
6. Press NEXT. Press + or – to select DAILY, WEEKDAYS OR WEEKENDS.
7. Press DONE to confirm and exit.
8. Press Start/Split or Stop/Reset to arm or disarm alarm. When disarmed, OFF will be displayed.
When armed, the alarm clock icon will appear
9. The INDIGLO night-light and alarm icon flashes and an alert sounds
when the alarm goes off. Press any button to silence. A back up alarm will sound after five
mintues if you don't press any buttons.
1. Press MODE repeatedly until TIMER appears.
2. Press SET. Hour digits flash.
3. Follow same pattern as setting TIME and ALARM to set hours (up to 24 hrs.), minutes, sec-
onds, and select between REPEAT/AT END (timer counts down and then repeats) or STOP/AT
END (the timer counts down and then stops).
4. Press DONE to confirm and exit.
5. Press START/SPLIT to start TIMER. Timer will continue to run even if you exit Timer mode. If
REPEAT/END selected
6. An alarm melody will chime and INDIGLO® night-light flashes when the timer has reached
zero or before it starts to count down again.
7. Press STOP/RESET to stop TIMER. Press again to reset to countdown time.
www.timex.com
W-90
FUNCTIONS
BASIC OPERATIONS
INDIGLO
DEMO
TIME/DATE/HOURLY CHIME/TIME ZONE
ALARM
TIMER
will flash. If STOP/END selected
866-095000
.
will flash.
+
START/SPLIT OR
(Increase value. Hold
to increase rapidly.)
–
STOP/RESET OR
(Decrease value. Hold
to decrease rapidly.)
(continued on reverse)