savic Dog Barrier Manual De Instrucciones página 3

EN FIXING YOUR DOG BARRIER DOOR AND WALL CUPS
Please refer to the pictures. Slide the 4 screw adjusters (B) into the
plastic bungs at each corner of your gate. Your gate must be fitted
with wall cups (D2), these should be placed around the top 2 screw
adjusters (B). Place the gate into the required opening, in the closed
position. To ensure that you secure the gate correctly, begin with the
screw adjusters (B) at the bottom of the gate. Ensure that your gate
is central, slide out the adjusters (B) and secure by fully tightening
the locking rings (C).
Next, adjust the top screw adjusters (B), once again ensuring that
your gate is central. Tighten the locking rings (C) until the handle is
aligned.
Once the bars of the inner and outer frame are parallel you can mark
the position of your wall cups (D2) with a pencil. Remove the gate
and secure your wall cups (D2) to your wall, doorway or stairway
using the sticky pads (D3) or screws (D1 + D4) provided (Do not
use sticky pads on wall paper or where there may be other loose
materials).
If using the screws, first drill a 1/4" (6 mm) hole into your wall and
insert the wall plug, then secure the wall cup with the screw. If you
are drilling into plaster board you will need to purchase expandable
wall plugs (available from DIY stores).
You can now refit the Dog Barrier door as instructed above.
Check that your gate is securely fitted. This check should be repeated daily to ensure that your gate remains securely
fixed and that all attachments and locking devices are operating correctly. (3)
USING YOUR DOG BARRIER DOOR
To open your gate:
Press the button, lift the lever and raise the door slightly.
To close your gate:
Align the handle with the frame and lower the lever until it clicks into place.
SAFETY TIPS
• Pets still need supervision and should not be left alone until they become familiar with the gate.
• A daily check on the gate is recommended to ensure that your gate remains securely fixed.
• Ensure that the gate is properly closed at all times.
• The gate is designed for indoor use only.
• A swinging gate can trap small hands.
• Dog Barrier is recommended for dogs, not for children.
• Do not allow older children to climb on or over the gate as this can result in an accident.
• Do not remove the safety instructions, you may not always be the user.
4
• Retain these instructions as you may wish to reposition the gate.
•
Warning!
Incorrect fitting or positioning of this safety barrier can be dangerous.
3
Warning!
• Do not use the safety barrier if any components are damaged or missing.
Warning!
• This barrier must not to be fitted across windows.
It should only take 5 minutes to fit your gate. We recommend that you carry out the installation away from young
children as some of the smaller components may present a choking hazard when loose.
CLEANING
Simply wipe with a soft damp cloth. Do not use harsh or abrasive cleaning agents.
EXTENDING YOUR DOG BARRIER DOOR
(4)
Some suggested configurations are pictured.
standard +1 extension +2 extensions
75 cm -› 84 cm 84 cm -› 91 cm 91 cm -› 98 cm
To fit your extension system (available separately, art. nr. 951098) first remove the screw adjusters (B) from the side
of your gate. Remove the plastic bungs from each corner of
your gate, (you may need to prise the bung out using a flat
screwdriver and tap lightly with a hammer). Push the extension
into place and press the plastic bungs back into your extension.
Slide the screw adjusters (B) back into place and fit your safety
gate as instructed in the FIXING YOUR DOG BARRIER DOOR
section. Note: Wall cups (D2) must be used when using an
extension. Please fit as described in the USING WALL CUPS
section. If a second or third extension is required, repeat this
)
procedure on the other side of your gate. (5
EN
+3 extensions +4 extensions
98 cm -› 105 cm 105 cm -› 112 cm
5