Simu T5 AUTO SHORT Guia Del Usuario página 4

Programming the first transmitter with the Hz receiver
5
>>
PROG 1s
Programming a new transmitter
6
>>
PROG 3s
>>
PROG 1s
- For group control with the new transmitter, perform operations 6.1 and 6.2 for each receiver of the relevant group.
- For general control with the new transmitter, perform operations 6.1 and 6.2 for each receiver of the installation.
- To delete an transmitter from the memory of a receiver, perform operations 6.1 with a programmed transmitter and 6.2 with the transmitter to be deleted.
Power up of the operator
7
>>
- It is advised to carry out these two opening/closing cycles as soon as the product is installed.
- For any further information, please consult the SIMU technical leaflet "T5 AUTO".
Recording and controling intermediate position
8
Recording :
- Position the motor on the wanted position.
- Press 5 seconds on the "stop" key. The motor
will run for 0.5 second in one direction and then
in the other.
Changing of the direction of rotation in user mode
9
>>
>5s
After stage 9.1, if no operation is carried out before 3 seconds (or if any operation different than 9.2 is made), the motor runs again briefly in
one direction and then in the other, and the rotation direction is not changed.
Cancelling programming
10
OFF ON
9.1 2s 9.2 7s 9.3
If you switch on/off the power to several receivers, they will all be in the cancellation mode. That is why you must "drop" all the recei-
vers that are not to be cancelled by controlling them from their individual control transmitter.
>>
PROG 7s
Warning: after stage 10.4, if nothing is done within 2 minutes, the motor will run again for 5 seconds in the direction opposite to that of 10.4.
Hereby, SIMU, declares that this equipment "T5 AUTO SHORT Hz" is in compliance with the essential requirements and other relevant provision
of Directive 1999/5/EC. A declaration of Conformity is available at the web address: www.simu.fr, heading "Normes". Usable in UE, CH.
- Press the "PROG" key for approximately one second. The motor will run for half a second in one direction and then in the
other. Your transmitter is now programmed to control the Hz receiver in stable mode. All transmitters that control only
one receiver may be used in §6 as an individual control for programming new transmitters.
6.1 - Open the memory of the receiver from the individual control transmitter:
- Press the "PROG" key of the individual control transmitter for approximately 3 seconds. The motor will run for half a
second in one direction and then in the other.
6.2 - Validate the operation from the new transmitter to be programmed:
- Press the "PROG" key of the new transmitter for approximately one second. The motor will run for half a second in one
direction and then in the other.
>> >>
>>
>2s
3s
OFF ON
2s 9.4
5s
10.5 - Confirm the cancellation of the affected receiver from the individual control transmitter:
- Press the Prog key of the individual control transmitter for more than 7 seconds. The motor will first run for
>>
half a second in one direction and then in the other. A few seconds later, it will run again in the two direc-
tions. The receiver is now as it was originally configured, and no transmitter and no settings is
saved in its memory and is ready for a new programming.
>>
Controling :
- Press on the "stop" key for 0.5 second. the
motor goes to the intermediate position.
5s
9.1 - Press on the Up and Down buttons at the same time for 5 seconds. The motor
rotates briefly in one direction, then in the other.
9.2 - Within 3 seconds, press on the Stop button for 2 seconds. The motor briefly rota-
tes in one direction, then in the other. The direction of rotation has been changed.
10.1 - Switch off the power supply to the receiver for 2 seconds.
10.2 - Switch the power to the receiver back on for 7 seconds.
10.3 - Switch off the power supply to the receiver for 2 seconds.
10.4 - Switch the power to the receiver back on.
- If the motor is on the end limit position (up or down), the motor will run briefly on one direc-
tion and then in the other, otherwise, the motor runs for 5 seconds in random direction.
The motor is now in the "cancelling" mode.
After the first two consecutive opening and closing of the
shutter :
- The motor memorizes automatically the end limit (up and
down) positions.
- The "stop on obstacle" function is activated.
0,5s
2 / 2