Viega ProPress Instrucciones Del Producto

Product Instructions
Viega ProPress Stainless
®
2½" to 4" Fittings*
*formerly ProPress Stainless XL
1 2
7 8
EN
Viega ProPress Stainless
2½" to 4" Fittings
For use only with Viega stainless steel tubing.
Viega products are designed to be
installed by licensed and trained plumbing
and mechanical professionals who are
familiar with Viega products and their installation.
Installation by non-professionals may void
Viega LLC's warranty.
DANGER!
Read and understand all instructions
for installing ProPress Stainless 2½" to
4" fittings. Failure to follow all instructions may
result in extensive property damage, serious injury,
or death.
1
Cut stainless steel tubing only with an approved
stainless steel pipe cutting tool. Cut the tube
square using a displacement-type cutter or fine
toothed saw.
Cut tubing a minimum of four inches
away from the contact area of the vise to
prevent possible damage to the tubing in
the press area.
2
Deburr inside and outside of the tube to the proper
insertion depths to prevent cutting sealing element.
Use a wire brush, Scotchbrite pad, sand cloth, or
sandpaper to remove loose dirt and rust particles
from the pressing area.
Viega LLC
585 Interlocken Blvd.
Broomfield, CO 80021
Phone (800) 976-9819
www.viega.us
3 4
9 10
3
Check the sealing element, separator ring, and grip
ring for correct fit. Do not use oils or lubricants.
4 Mark the proper insertion depth as indicated by the
ProPress Stainless 2½" to 4" Insertion Depth Chart.
Improper insertion depth may result in an improper seal.
ProPress Stainless 2½" to 4"
Insertion Depth Chart
Tube Size (in) 2½
/
Insertion Depth (in) 1 1 1
16
5
While turning slightly, slide press fitting onto tubing to
the marked depth. End of tubing must contact stop.
6
Press Viega ProPress Stainless 2½" to 4" fittings
with Viega ProPress XL-C rings and V2 actuator.
Use only rings that are compatible with
ProPress XL-C fittings.
Do not use rings intended for 2½" to 4"
Bronze fittings.
7
Open XL-C ring and place at right angles on the
fitting. Ensure that the XL-C ring is engaged on the
fitting bead.
8
With V2 actuator inserted into the press tool, open the
V2 actuator. Connect the V2 actuator to the XL-C Ring.
Look at insertion depth mark on the tube to make sure
that the tube is properly inserted into the fitting.
WARNING!
Keep extremities and foreign objects away
from press tool during pressing operation
to prevent injury or incomplete press.
Product Instructions
EN
Viega ProPress Stainless
2½" to 4" Fittings
This document is subject to updates. For the most current Viega
technical literature please visit www.viega.us.
Instrucciones del producto
ES
Accesorios Viega ProPress para
acero inoxidable de 2½" a 4"
Este documento está sujeto a actualizaciones. Para obtener la
documentación técnica más reciente de Viega, visite www.viega.us.
Instructions produit
FR
Raccords ProPress de Viega en
acier inoxydable 2½" à 4"
Le présent document est soumis à des mises à jour. Pour consulter
les manuels techniques Viega les plus récents, veuillez visiter
www.viega.us.
PI-PP 519074 1119 ProPress Stainless 2½ to 4 (EN ES FR)
5
9
Hold the trigger until the actuator has engaged the
XL-C ring.
10 Upon completion of the press, release the V2
actuator from XL-C ring. Remove the XL-C ring
from fitting. Remove product instruction label from
fitting to indicate that press has been completed.
Pressure Testing with Smart Connect
Unpressed connections are located by pressurizing
3 4
the system with air or water. When testing with water
/
1 1 5 2⅜
the proper pressure range is 15 psi to 85 psi. When
16
testing with compressed air the proper pressure
range is ½ psi to 45 psi maximum. If testing with
compressed air, use an approved leak-detect solution.
Following a successful pressure test, the system may
be pressure tested up to 200 psi with air or up to 600
psi with water.
Testing for unpressed connections using
Smart Connect is not a replacement for
pressure testing requirements of local
codes and standards.
CAUTION!
It is the responsibility of designers of
piping systems to verify the suitability
of type 304 and 316 stainless steel pipe for use
with the intended fluid media. The fluid's chemical
composition, pH level, operation temperature,
chloride level, oxygen level, and flow rate and their
effect on AISI type 304 or 316 stainless steel must
be evaluated by the material specifier to confirm
system life will be adequate for the intended service.
Failure to do so may cause serious personal injury or
property damage. Contact Viega Technical Services
for questions and approvals.
6 6
®