LAZBOY La-Z-Touch Instrucciones De Operación página 9

®
La-Z-Touch 10-Motor Massage & Heat Recliner
Operating Instructions:
Review Important Safety Instructions at the front of this booklet before operating.
Plug in the Power Transformer. Make sure there is enough slack in the cord
running from the chair to the outlet to allow for rocking and reclining. Never
stretch or strain a cord.
NOTE: Automatic Timer Operation
The system has an automatic timer that will shut off the MASSAGE and HEAT
functions after approximately 15 to 30 minutes of operation.
• Pushing down on the POWER button or either zone button will restart
the massage.
• Pushing down on the HEAT button will restart the heat. Push down once
for Low Heat and twice for High Heat.
• When you are finished, make sure to push the POWER button and the
HEAT button (if activated) to turn the unit off. Press the HEAT button
twice if in Low Heat setting.
• The timer will also reset if you unplug the Power Transformer or if there
is a power outage.
NOTICE:
The massage and heat functions may start automatically when
electrical power is restored after a power outage. The timer should automatically
shut down the massage and heat within 15 to 30 minutes. There should be no risk
of injury or damage if this happens.
Troubleshooting for Chairs with 10-Motor Massage & Heat
There are no user maintenance or repair requirements. If the massage or heat
function does not work:
1. Make sure the Automatic Timer Operation has not been activated. Press the
POWER button to restart the massage. Press the HEAT button to restart the heat.
2. Make sure the Power Transformer is plugged into an electrical outlet.
3. Make sure the electrical outlet is working. For example, make sure there are
no blown fuses or tripped circuit breakers.
4. Make sure all the connectors are secured; refer to the Assembly Instructions.
5. Make sure that the electrical cords are not crimped or pinched. Make sure
the electrical cord or plug is not damaged. If the massage system still does
not operate properly, contact your dealer for instructions on returning the unit
for examination and repair. Except for replacement of the Power Transformer,
never attempt to make any repairs or adjustments yourself.
Power Transformer Replacement
If the Power Transformer must be replaced:
1. Unplug the Power Transformer from the electrical outlet.
2. Locate the Power Transformer connection; refer to the Assembly Instructions.
Gently pull the connectors apart to disengage.
3. Push the replacement Power Transformer connector into the mating connector;
refer to the Assembly Instructions. Make sure the connectors are secured with
no gaps between them.
16
®
La-Z-Touch 10-Motor Massage & Heat Recliner
Operating Instructions:
POWER
Activates system when
button is backlit with LED.
Press once for 15-min.
timer. Press and hold
down for 30-min. timer.
NOTE: To restart unit after
timer shuts off, press
either ZONE or PWR button.
ZONES
Activates any or all zones.
LED indicates which
zone(s) has been selected.
1 Upper Back
2 Lower Back
3 Hip Region
4 Upper Thigh
5 Lower Thigh
PULSE MODE
Activates 3 pulse settings.
PULSE, TAP and ALT.
(alternating pulse & tap)
in active zones.
INTENSITY
Will increase (+) or decrease
(-) intensity during all modes.
SWELL
Increases and decreases
intensity cycling in all modes.
Use FAST and SLOW to adjust
speed of intensity.
LA-Z-TOUCH ® 10-MOTOR MASSAGE & HEAT TRANSFORMER SPECIFICATIONS:
Input: AC 120V 60 Hz 36 W
Output: AC 12V 2000mA
Save These Instructions
HEAT
Activates heat. Press
once for low and
twice for high. Use
independently or
with massage.
NOTE: Heat will
deactivate in 30
minutes. To restart, press
the HEAT button again.
WAVE MODE
Activates 3 wave-like
settings (1-5-1, 1-5 or
5-1) in active zones.
CIRCLE MODE
Activates clockwise (CW),
counterclockwise (CCW)
or figure 8 (FIG 8)
pattern in active zones.
SPEED
Controls pulsing
frequency of massage
in PULSE mode and
controls velocity as
it cycles through in
WAVE mode.
Press (+) to increase
and (-) to decrease.
PROGRAM
Provides ability to
program intensity
levels in each zone.
See Programming
Instructions.
17